The best chainsaws according to consumers: choosing a powerful and functional tool

Even at the beginning of the last century, the process of felling trees was a difficult and labor-intensive process, but in the 20s the first chain saws began to be produced. Since that time, technological progress has not stood still, and today many different models are produced. So that you can choose a good chainsaw that is not inferior in quality and reliability to its professional counterparts, we have compiled a rating of the best chainsaws for the garden and at home, which included a wide variety of models from popular manufacturers of this category of goods.

Basic criteria for choosing a chainsaw

Before you start buying a chainsaw, you need to decide what you are going to use this tool for. It is no secret that the cost of this type of tool is determined by a combination of factors such as power, operating time - that is, the class. Modern chainsaws are divided into three main classes:

1. Household. These saws are great for garden work and simple repairs.
2. Semi-professional ones are used for more complex work, including construction.
3. Professional saws are the most powerful and reliable among chainsaws, designed for industrial felling.

Chainsaw power

The performance of a chainsaw directly depends on the engine power. The maximum power rating for this gas-powered tool reaches 7 kW, which corresponds to 9 hp. Such saws are used in logging. The power of household devices does not exceed 2.5 hp, semi-professional ones are produced with engines up to 3.5 hp, and professional ones have a power of up to 6 hp.

Weight

Low-power household devices weigh the least. Increasing the power of the saw usually entails increasing the mass of the tool. The average weight of gasoline chain saws ranges from 3 to 6 kg.

Fuel consumption

An additional aspect when choosing a gas-powered tool is its efficiency. Household-grade products are the most economical, while professional ones, on the contrary, are more voracious. The volume of a chainsaw tank is traditionally calculated for 40 minutes. work, so the larger the fuel tank of the model, the greater the fuel consumption will be.

The principle of operation and design of a chainsaw

Chainsaws are used in a wide variety of conditions: from small work in the garden (trimming branches, twigs, removing unnecessary wood), to construction and professional logging. The small tool is completely autonomous, as it runs on fuel. It can be taken far from civilization and work all day long, if you have an additional canister. The unpretentious device rarely breaks and is easy to repair.

The operating principle of the tool is to operate an internal combustion engine, for which there is a small fuel tank and an oil reservoir. The rotation of the power unit transmits torque to the sprocket, which includes the legs of the chain. The movement of the links is started along a tire consisting of two connected strips. There is a groove on its edge, thanks to which the legs sit deeply and the chain does not fly off.

Sawing is carried out by rotating the chain at high speed, which reaches 9000 rpm. The link structure has protruding tenons that engage the wood fiber and cut it. The operator holds the device suspended by two handles. One has keys for starting rotation, as well as a lock against accidental activation. The engine starts from a cable starting mechanism.

Depending on the engine size, the tool can be used from 2 to 16 hours. Most models are equipped with an emergency chain brake system that is activated if an urgent stop of rotation is required. The tension of the cutting element is carried out by the movement of the bar in the grooves and its fixation with bolts or a clamping screw. The latter allows you to adjust the chain within a minute and immediately continue working.

The chainsaw includes the following elements:

• motor;
• fuel tank;
• two handles;
• guide bar;
• saw chain;
• protection shield;
• starting device;
• gear stop.

Additional criteria for choosing a chainsaw

Additional, but important “little things” when working with gasoline chain saws include:

• Anti-vibration system. Its presence is necessary when working with the tool for a long time.
• Air filter. Protection from dust contamination ensures longer operation without the need for early repairs.
• A reliable brake is an important criterion for tool safety. Depending on the manufacturer, they can be equipped with an anti-vibration and kickback protection system, the so-called inertia brake.
• The length of the bar determines the length of the cut. When choosing a tool, do not forget that the linear size of the bar must be consistent with the power of the saw.
• Long tires on low-power units will lead to their rapid failure.

We will review chainsaws of each class and make a rating of the best models, according to user reviews.

Criteria for evaluation

When choosing a tool yourself, take into account:

• real cost of a chainsaw;
• efficiency and traction characteristics of the drive;
• level of technical equipment;
• in some cases - maintainability and interchangeability of spare parts with similar designs from other brands.

Marketing analysis shows that a good inexpensive chainsaw meets the basic parameters of the needs of ordinary people, agricultural farms, forestry and park management workers.

By all accounts, the best chainsaw for home and garden is an economical, simple in design, easy to use and durable model from a popular brand with a capacity of one and a half to three horsepower. A budget chainsaw, due to its limited capabilities, is most often purchased to perform one-time dismantling or construction work.

The top 10 best chainsaws published in the information field consists of new models from the brands Shtil, Husqvarna and Hitachi, known for the impeccable quality of their products. A test of chainsaws from these manufacturers proved their full compliance with the stated service and operational requirements.

The list also includes several popular tools from the ALPINA A 3700 and Daewoo brands. According to experts, these developments will take leading positions in the “Best Chainsaws of 2021” rating.

The offered range of gasoline-powered saws from different brands can be divided into 5 groups.

The best inexpensive chainsaws (up to 10,000 rubles)

Household series saws are the most common class, having a minimum of functionality, but perfectly suitable for work in the country, in the garden and for small construction work. In addition, due to their short service life (from 400 to 1000 hours), compactness and low weight, they are relatively cheap. If you are looking for a tool for household needs, then a household saw is the best in terms of price and quality.

PARTNER P340S

The Chinese model of the Husqvarna chainsaw, produced under the Partner P340S brand, is a household-class tool and is intended for short-term gardening and construction work, and collecting firewood. This budget chainsaw is ergonomic and easy to use. It is equipped with a reliable braking system, has a low level of vibration and noise, which is rare in tools of this class, and is distinguished by high quality components and good fit of parts.

Advantages:

• a fuel pre-priming pump significantly improves engine starting, especially in the cold season;
• light weight;
• anti-vibration system reduces the load on the operator’s hands;
• low consumption of fuel-oil mixture.

Flaws:

• demands on the quality of fuel and oil;
• there is no window for visual monitoring of the remaining oil and fuel;
• there is a possibility of spontaneous unscrewing of the intake manifold fasteners during operation.

Echo CS-353ES-14

The inexpensive but good chainsaw Echo CS-353ES-14 is an excellent saw for preparing firewood in the country or at home, or cutting down small trees. The presence of carburetor heating allows you to use the Echo CS-353ES-14 in winter. Steel springs and rubber shock absorbers, which this model is equipped with, significantly reduce vibration during operation. The use of advanced Japanese technologies makes it possible to combine maximum comfort in use and high performance. Even though it is produced in China.

Advantages:

• ergonomic design;
• best in power in its class;
• easy and quick to start;
• The presence of the G-Force air purification system allows you to clean the air filter less frequently.

Flaws:

• inconvenience of refueling;
• absence of a window for monitoring the remaining fuel and oil.

Makita EA3202S-40

The Makita EA3202S-40 chainsaw is a convenient chainsaw belonging to the household appliances segment and has a 1.81 hp engine. Thanks to the electronic ignition and primer, it starts easily. This model has an active vibration damping system, a SafetyMatic chain brake and an adjustable oil pump. Unlike previous models from this manufacturer, it has virtually no complaints from users. Among the household saws reviewed, the Makita EA3203S-40 is one of the best chainsaws in the rating. Although Makita is recognized as the best manufacturer of power tools, gas powered tools of this brand are also worthy of attention.

Advantages:

• light weight, easy start;
• convenient chain tightening;
• low noise level during operation;
• large volume of fuel tank;
• possibility of adjusting the oil supply to the saw chain;
• The best in its class in terms of price and quality ratio.

Flaws:

• According to user reviews, one drawback is the sensitive start button, but this is rather a matter of habit.

How to choose a chainsaw

Semi-professional models perform any work - from repair and construction to tree felling. Their only drawback is the inability to use 8-10 hours a day for a long period. They often serve as loppers in logging. Professional saws have high power (usually more than 2.5 kW) and are characterized by a wide range of functions. They are used mainly as shaft saws; they can work tirelessly all year long, 10-16 hours a day. The main feature of a professional tool is 8 hours of work without interruption. Such saws are made from durable and wear-resistant materials, and their service life ranges from 1300-2000 operating hours (for household models this figure is 2-3 times lower).

Work resource. There is no precise and clear definition of the concept of “work resource” that would be used equally by all manufacturers and sellers. Ordinary people interpret it as the time until the tool is sent to a landfill, and experts - as the time until the first major engine overhaul or a reduction in compression by 40%. As you can see, it is quite difficult to give an exact figure, and almost impossible, so the main focus here is on the availability of a branded service. The main advice for operating a chainsaw (as, indeed, any other tool) is this: choose the right operating mode and avoid significant overloads. The formula of love is right here too: how an instrument is treated is how it serves. Cutting speed When purchasing a chainsaw, buyers often ask about the speed of sawing wood with a tool of a particular brand (for example, whether it is necessary to apply pressure while doing this). First of all, it depends on the condition of the saw set, and in particular the chain. When working with a dull chain, cutting efficiency drops significantly, and the likelihood of saw failure increases as the load on the engine increases. Therefore, with a professional approach to the process, it is recommended to regularly adjust the chain (for example, at the end of the working day). In addition, the shape of the cutting tooth and the pitch of the chain make a significant contribution to productivity. The best result is achieved with optimal selection of chain and engine power. The power of the saw is the second important parameter that characterizes its activity and determines the strict conditions for the applicability of this model.

The problem of kickback The most dangerous moment during the operation of a saw is the so-called kickback, or a sharp throw of the tool towards the operator. This happens when the end of the saw bar meets the surface of the wood being processed. The only way to protect yourself from injury is to quickly stop the chain. This function is performed by a special brake (it is called inertial), the drive for which is a shield located in front of the operator’s left hand. It is a kind of lever that can occupy two positions. Before starting, the shield switches to the position “closer to the hand” and thereby is cocked. At the moment of the reverse impact, the operator's hand rests on it, and the shield is activated, instantly activating the chain brake. In addition, it can change position without interaction with the operator's hand - simply due to inertia. Another way to avoid kickback is to exclude the dangerous sector from the sawing process. This is done with the help of another shield (protective sector), covering the end of the saw set and preventing the tool from kicking. However, this method is used much less frequently than installing a chain brake. Moreover, Swedish saws (Husqvarna, Jonsered, Partner) are deliberately not equipped with such guards. The reason is that Swedish safety standards require that the end of the tire be used. Felling a tree by a Swedish lumberjack is very similar to cutting a loaf of bread: the operator first bites into the wood with the end of a tire, and then makes a circle around the trunk. This way you can fell a tree twice as thick as the length of the tire. In Russia, this method is allowed only to highly qualified fellers.

Anti-vibration system Prolonged contact with a strongly vibrating tool can lead to serious joint diseases, so the presence of an anti-vibration system is simply necessary, especially on professional models. The simplest type is a set of rubber gaskets located between the handles and the body. However, such an anti-vibration system is already practically irrelevant - in modern chainsaws, as a rule, the principle of two masses is implemented: the engine block is separated from the handle block and the fuel tank. Anyone who has ever worked with a powerful saw for several hours in a row knows what a huge load the hands experience due to vibration. In the absence of sufficient vibration protection, this is fraught with impaired blood circulation and other unpleasant consequences. Therefore, if there is no desire to acquire occupational diseases along with the specialty of a lumberjack, you should pay attention to what kind of vibration protection this system provides. It’s even better to ask when purchasing to start the chainsaw and hold it in your hands.

Power and weight Manufacturers avoid increasing the power of household models, as this leads to an increase in the weight of the tool. In addition, high power is not the most important factor when using a chainsaw in the household. A favorable weight-power ratio is also important for a professional, since this parameter significantly affects the convenience of work and, as a consequence, the quality of work. In general, the class of professional chainsaws is characterized by a significantly greater spread in power (from 2 to 6 kW) than for household ones. This is explained by the variety of conditions in which such a tool is used (tree trunks of different thicknesses, hard or frozen wood, etc.). In Russia, professional felling is carried out in winter, since forests are usually impassable in summer. Wood is frozen and hard in winter, so for felling you should choose especially strong and durable chainsaws.

Types of Bars There are several types of saw bars and chains designed for different purposes and users. The saw set for household saws will suit those users who use the tool occasionally and do not have any special professional skills. To keep these operators as safe as possible, manufacturers install a narrow, flat bar with a low-profile chain that has very little tendency to kickback. Lightweight tires are optimal for work in which the weight of the chainsaw plays a certain role (for example, sawing at height). Such tires consist of two steel plates with selected grooves, the voids between them are filled with polyamide. This design allows you to significantly reduce the weight of the tool. For professional use and long-term operation, tires with replaceable heads have been created. They are installed on saws of medium and high power.

Bar length In the technical specifications of a chainsaw, the word “recommended” is usually added to the bar length indicator. What does this mean? The fact is that the longer the tire, the greater the resistance it provides to the torque of the engine crankshaft. If the power of the chainsaw is insufficient, additional efforts will have to be made, which will lead to premature wear of the saw set and the engine. In addition, since most of the power will be wasted, fuel consumption increases. Thus, the length of the bar must be consistent with the power of the saw, and “recommended” essentially means maximum (shorter bars can be used, but longer ones are not advisable).

Chains Low profile chains are intended for non-professional use. As a rule, their pitch is 0.325 inches, so the main advantage of such a chain (minimum level of vibration) smoothly flows into its disadvantage - reduced performance. On heavy-duty chainsaws, 3/8- and 0.404-inch pitch chains are recommended. Their vibration level is increased, but their activity is much greater. These chains are optimal for felling and bucking thick trees. There is also a special class of tasks that conventional chains cannot cope with (they become dull very quickly). This is sawing contaminated or frozen wood. For such work, there are special chains with carbide tips.

Why 3/8 and not 0.375? Many have repeatedly wondered what a chain pitch is and why it has such strange designations: in one case - in the form of a decimal fraction, and in another - a simple one. The answer is that theoretically the pitch is the distance between the two nearest teeth, while practically it is the distance between the rivets of the chain, divided in half. Chain pitch is measured in inches and can be equal to 0.325; 0.375 or 0.404. As world experience has shown, users often confuse numbers in labeling, because 0.375 and 0.325 differ in only one digit. To avoid such incidents, manufacturers decided to adhere to a unified designation system, according to which the chain pitch takes three values: 0.325, 3/8 and 0.404 inches.

How to choose a saw set It should be remembered that the components of a saw set (chain, bar, drive sprocket, or sprocket) from different companies are usually incompatible. The differences lie in the parameters of the drive sprocket (in accordance with which the chain pitch must be) and the thickness of the drive chain link, which varies within 1.3-1.6 millimeters. Therefore, having chosen a specific model, be it an electric or chainsaw, the buyer almost always becomes a fan of components of the same brand. Many people believe that the larger the chain pitch, the more aggressive it is. In reality, everything is somewhat different. It turns out that the aggressiveness of a saw with a particular chain greatly depends on power and, accordingly, torque. The power of the tool determines the saw's ability to pull the chain through the cut. It was this process that the designers of many companies struggled with. As it turned out, for saws with a small cylinder volume (and therefore low power), it is unprofitable to install chains with a 3/8-inch pitch - with a wide tooth pitch, the chain bites into the wood more strongly, but the engine is not able to pull it through. The result is uneconomical work with only part of the canvas. Conversely, high-power saws equipped with a 0.325-inch chain simply pull the chain through without actually touching the wood. The following pattern was derived. For saws with a cylinder capacity of 40-50 cubic centimeters, a chain with a 0.325-inch pitch is more effective, while for more powerful machines a 3/8-inch pitch is optimal. Moreover, in the category of 40-50 cubes, both chains are used - the choice is determined by the specific features of the model. There is another category - powerful saws with high torque (for example, the domestic Ural-2TE). Chains with pitches of 0.404 inches are possible on these machines. And finally, we must not forget: when changing the chain to another with a different pitch, you will also have to replace the drive sprocket.

Requirements for gasoline and oils Any saw is equipped with a two-stroke carburetor engine and two tanks (one for filling the fuel mixture, the other for oil for lubricating the chain). The volume of the fuel tank is from 0.3 to 1 liter, and the volume of the oil tank is usually 1.5-2 times less. This volume ratio leads to the fact that the chain oil and fuel mixture run out approximately simultaneously, namely after 30-45 minutes of operation (at full load). The need to prepare a fuel mixture is clear to anyone who is familiar with two-stroke engines: the difference in the operating cycle of a two-stroke engine from a four-stroke engine leads to the fact that to lubricate all the rubbing parts (piston, shaft, etc.) it is impossible to use a system of oil pumps, and oil must be used add directly to gasoline. All this is quite important, since if you try to work only on gasoline or violate the proportions of the gasoline-oil mixture, the tool will quickly break. Recommendations for the brands of gasoline and oil, as well as for the proportions of the fuel mixture, are as follows. For Russian chainsaws, they use 76 gasoline and conventional oils for two-stroke engines (motorcycle oils), which are added to the mixture in an amount of about 4%, that is, in a proportion of 1/25. Foreign models require gasoline with an octane rating of 92 (or higher) and branded oils from chainsaw manufacturers (the oil content in such a mixture should be about 1/40). In principle, domestic oils for two-stroke engines are also suitable for foreign chainsaws, but two circumstances should be kept in mind. First of all, you need to be sure that the gasoline is clean. Second: motorcycle oils are designed for engines with speeds up to 8.5 thousand per minute, and since foreign-made chainsaws can reach speeds of 11-14 thousand, the use of these oils reduces the service life of the tool by an average of 7-10%. So whether the game is worth the candle, you will have to decide for yourself. It’s easier with oil to lubricate the sawing machine: in all models of household and professional chainsaws you can use regular oils for Lada cars (for example, motor oils are recommended for Husqvarna models, and transmission oils are recommended for Stihl models). You should also pay attention to the features of seasonal operation of the tool. If the saw operates at low temperatures, then even with the correct selection of all ingredients, the quality of the oil and fuel mixture may be unsatisfactory (crystallization occurs and viscosity increases significantly). In this case, the saw itself must be adapted to such conditions - for example, it is necessary to provide for the possibility of warming up the carburetor during operation. In addition, it is advisable to first warm up the saw (if it was stored in an unheated room) to avoid undesirable consequences due to the presence of condensation.

Purchase and operation When purchasing a saw, the natural desire of every buyer is to check the functionality of the tool. There are pitfalls in this seemingly simple process. It's all about the design features of chain saws. Please note: any chainsaw cannot be started without a pre-installed and adjusted saw set (bar, sprocket and chain), otherwise the clutch will immediately fall out. So there is no need to rush to pull the cable - it is better to read the instructions carefully. (By the way, if an imported saw has entered our market officially, the instructions must certainly be in Russian.) After purchasing a chainsaw, you should definitely run it for 40-50 minutes at low speeds (this approximately corresponds to the exhaustion of the fuel tank), then turn off the engine and check chain tension. Next, you need to make several cuts, applying little effort, and only then proceed to full operation. Each new chain (or bar) should be run in for a few minutes. All this is done so that the sprocket, bar and chain warm up well and the oil gets onto all lubricated parts of the saw set. In approximately 90% of cases, the cause of saw failure is negligence in the saw set, and in particular poor care of the chain. In other words, when the chain is sharpened, it does the work; when it is dull, the person does the work. In addition, there is an additional increased load on the engine. In addition to the obvious inconveniences, such an increase in load leads to a significant reduction in the service life of the tool.

How to quickly start a saw After the mandatory pre-start check of the saw set and refueling with fuel and oil, the saw is ready for work. Next, you need to pull out the choke, completely remove the slack in the starting cable and start the tool with a strong jerk (with sluggish tension, there is a high risk of flooding the spark plug, which will somewhat complicate subsequent starting attempts). If everything is done correctly, the saw starts the first time.

The best semi-professional chainsaws

More serious tools include semi-professional or farm-grade chainsaws. Possessing average power and a higher service life, models of this class are suitable for operation up to 5 hours a day, but with significant interruptions in operation. A good semi-professional saw will become an indispensable assistant when running a personal subsidiary or farm. Procuring firewood for the winter season, construction and repair work, clearing an area of ​​old trees - chainsaws of this class can handle all this perfectly.

Echo CS-260TES-10

The lightest saw in the rating, Echo CS-260TES-10, is designed to work with any type of wood. This chainsaw is light and convenient, weighing only 2.9 kg; a special coating on the body increases its wear resistance. Thanks to the light weight of the saw, it can be used at heights and safely carry out the necessary work with one hand. Electronic ignition and easy start system allow you to work in any conditions. The oil pump is made according to a professional design and supplies lubricant to the saw chain only during the sawing process. The engine power allows you to install a longer tire.

Advantages:

• light weight;
• small dimensions;
• easy start;
• reliability in operation;
• Conveniently suitable for one-handed operation.

Flaws:

• Monitoring user reviews did not find any complaints about the operation of this model.

Oleo-Mac 941 C-16

One of the best all-purpose semi-professional saws, Oleo-Mac 941 C-16, provides maximum performance when working. Thanks to the presence of a three-jaw clutch, a chrome-plated piston, as well as a crankshaft and connecting rod made of forged steel, the chainsaw has high reliability and characteristics that bring it closer to the class of professional saws. Easy starting is ensured by an electronically controlled magneto, and an automatic oil pump ensures zero oil consumption at idle. According to the owners' reviews, this is a high-quality, durable and convenient chain saw.

Advantages:

• powerful two-stroke engine;
• easy starting in any weather conditions;
• reliability;
• ease of use.

Flaws:

• high noise level;
• inconvenient location of the chain tensioner mechanism.

Husqvarna 450e

Husqvarna saws are rightly considered one of the best. The Husqvarna 450E chainsaw is no exception. In terms of reliability and quality, it ranks among the best semi-professional saws. With a small weight, it has a fairly powerful 3.2 hp engine. An ergonomic handle, quick access to the filter and spark plug (the cylinder cover is secured with latches), fuel level indication and markings for the direction of tree felling make it much easier for the operator to work with the Husqvarna 450e.

Advantages:

• easy starting even after a long period of inactivity;
• reliability of components;
• efficiency;
• good power reserve.

Flaws:

• high price;
• expensive spare parts.

Stihl MS 260

The most popular chainsaw in the ranking, the Stihl MS 260, occupies the leading position of semi-professional saws. Thanks to its versatility, power and durability, it is deservedly popular among lumberjacks and builders. Suitable for both felling and construction work. With a relatively low weight, it has a good reserve of power, which allows it to be used throughout the day in any conditions. It is equipped with tires 37 and 40 cm long, but its power allows you to install long tires up to 50 cm.

Advantages:

• ease of launch;
• low vibration level;
• high quality chain and tire;
• ease of maintenance and cleaning.

Flaws:

• none.

TOP 5 inexpensive and reliable budget models

Huter BS-52

This model has a semi-professional level, confirmed by:

• installation of a drive with a working cylinder capacity of 52 cm3 and a power of up to 3.4 hp;
• high-performance sawing device 20 inches long;
• the presence of starting, lubrication and operational safety systems typical for semi-professional models.

The Huter BS-52 gas-powered saw, costing up to 5,500 rubles, is one of the few developments that combines a budget price with increased productivity and quality of standard components.

PATRIOT PT 3816 Imperial

A household saw with a dead weight of 5.4 kg is equipped with a 38 cc power unit with a power of 2 hp. A characteristic feature of the product is the presence of a full set of technical equipment, including a quick engine start system for automatic dosing of chain oil supplied to the Oregon set.

Optimal operating conditions for the operator are ensured by the effectiveness of the standard vibration damper and muffler, and the easy-to-grip shape of the body and handles.

Hyundai X 360

The functionality of the South Korean chainsaw X 360 series, successful in all respects, is focused on a range of household and construction work. The household-grade tool is equipped with a standard 37.2 cm3 power drive with a power of 1.6 hp. and a branded 14-inch Hyundai tire with a wear-resistant Oregon saw chain.

The model with a base price of 6,400 rubles includes:

• starter with quick start device EASY START;
• convenient location of the chain adjustment mechanism;
• saw mechanism lubrication system;
• high level of operational safety with minimal response time of the emergency stop brake.

DAEWOO DACS4516

A gas-powered saw from the famous South Korean manufacturer of household goods, Daewoo, occupies a worthy place in consumer ratings. In particular, the demand for the semi-professional model of the DACS4516 series has stabilized in the Russian market of household gasoline-powered tools.

The tool with modern technical and operational parameters is powered by a two-stroke carburetor 45.2 cc engine with a power of 3.1 hp.

In terms of design, the saw can be easily distinguished from models with similar purposes:

• widespread use of light alloys;
• complete dust and moisture protection;
• the presence of wear-resistant nickasil coatings on the piston drive group.

The tool kit also includes a low-profile chain with a smooth entry into the cut and a plastic case that is convenient for transporting the saw.

Partner P350S

A general purpose household saw can be used with equal success in a wide range of construction and commercial sawing work. The 410 mm professional tire is powered by a 2-horsepower engine with a displacement of 38 cm3.

The cost of the tool, around 9,000 rubles, is many times compensated by the high reliability and long service life of the saw, economical fuel consumption and long-term operation at high speeds with minimal working time spent on cooling the power unit.

The list of design features includes handle-mounted controls and a carburetor with automatic choke control.

The best professional chainsaws

Professional-grade saws are used for continuous operation over a long period of time, have high performance and reliability. The ability of such a tool to work 8 hours a day for many years is achieved through the use of durable, wear-resistant materials in its manufacture. Such saws are intended primarily for felling timber on an industrial scale, but are also used in construction and the procurement of firewood in large volumes.

Husqvarna 395XP

The Husqvarna 395XP professional saw is used for sawing hardwood. It has quite high performance and power of 7.1 hp with low weight for a tool of this class. High engine torque ensures fuel economy. The model is equipped with an excellent vibration protection system, an easy start and quick start function and a centrifugal air purification system. For long-term operation, the saw is equipped with an ergonomic grip that does not tire your hands when loaded.

Advantages:

• adjustable oil pump;
• durable crankcase made of magnesium and aluminum alloy;
• quick-release air filter mount;
• high power.

Flaws:

• high noise level, it is simply impossible to work without headphones.

Stihl MS 661-28

The Stihl MS 661-28 chainsaw is designed for extreme workloads and has high performance and power. This is the best model for harvesting large-sized wood. This model is equipped with “non-losing” nuts for fastening the chain sprocket cover, which is very important when working in the forest. The anti-vibration system is quite high quality; the saw does not create a load on the body. The presence of a compensator ensures efficiency and constant power of the unit. The carburetor is heated and has a winter-summer mode switch.

Advantages:

• power and high performance;
• easy start;
• single-lever control provides comfort during operation;
• effective anti-vibration system.

Flaws:

• high price compared to competitors.

EFCO MT 8200

The gasoline chain saw from the Italian manufacturer EFCO MT 8200 is perfect for logging work and construction sites, as well as for owners of country houses. The model is equipped with a decompressor, thanks to which even a beginner can handle starting the chainsaw. The controls are conveniently located on the saw handle. Due to the original electronic coil, the cooling of the mechanism is improved. Light weight and anti-vibration system create comfortable operation.

Advantages:

• easy start;
• convenient control;
• reliability and durability.

We recommend watching an interesting video on how to choose the right chainsaw!

Review of the Makita DCS7901-70 model

This model was developed in the center of innovation and invention - Japan. Leading engineers and technologists worked on the creation of a powerful and practical chainsaw, who were able to achieve the best results. The main production of the brand is located in Germany, where they produce professional equipment that is reliable and highly productive.

The sales kit includes:

• combination key;
• chain;
• tire;
• case for protection.

The power and weight of the product are ideally comparable, the optimal proportions of all structural elements allow you to use the saw without any difficulties. The ergonomics and convenience of the equipment correspond to the highest standards. The saw starts literally with a half turn thanks to the presence of a decompression valve. During operation, a vibration protection system is activated, which provides:

• Ease of use;
• minimal noise pollution;
• accuracy of cuts;
• minimum level of error.

The high-tech structure of the structure provides a simple and understandable method of servicing the equipment. The device has modern air filtration, which extends the life of the product and preserves the safety of the environment. The complex configuration of the product does not interfere with the operator’s use, since the saw has minimal weight for such dimensions. There is approximately one horsepower per kilogram of device weight.

The manufacturer clearly controls all stages of the production process, selects only high-quality materials for production and closely monitors the accuracy of assembly. The entire production process is fully automated, so the possibility of defects is completely eliminated. The brand does not stop improving the conditions and technologies for the production of gasoline saws.

There is no doubt about the reliability and durability of the Makita DCS7901-70 saw engine, because the crankcase is made of magnesium alloy, which is incredibly stable and durable even at high speeds. A special oil distribution system inside the engine eliminates the possibility of breakdowns. Modern internal coating will never allow the device to fail at the most inopportune moment.

The efficiency of the device is based on the maximum level of fuel combustion. This feature was made possible thanks to the presence of a four-chamber purge and an electric ignition system. Such innovations help to increase the efficiency of the device’s motor, which leads to increased fuel economy.

Not only main fuel is saved, but also lubricating oil. An automatic oil supply system allows you to control consumption. You can also adjust the oil supply speed for lubrication of the Makita DCS7901-70 saw headset.

The internal structure of the equipment allows the saw to be used in a wide variety of environmental conditions. Even at low air temperatures, the device continues to work smoothly, showing the highest productivity indicators.

Advantages and disadvantages

Makita DCS7901-70 has the following list of positive characteristics:

• efficiency;
• high levels of ergonomics;
• modern equipment;
• use of high-tech materials in the manufacture of components;
• Airmaster system;
• resistance to negative environmental influences;
• high productivity;
• possibility of use in large-scale works;
• modern oil supply system.

Flaws:

• relatively high cost;
• dependence on expensive energy resources;
• complexity of the design.

Reviews

Reviews from customers who have already purchased or tested a professional saw indicate a positive attitude towards the brand. Consumers trust the German assembly, emphasizing the extensive experience and high qualifications of specialists.

In operation, the Makita DCS7901-70 showed excellent performance; even large-scale work did not affect the efficiency and productivity of using the device. Despite the high power of the device, energy consumption remains low. A modern fuel economy system allows rational use of both oil and gasoline.

You can learn more about the model by watching the video review:

Let's compare the models

Model	Power, W	Chain pitch, inches	Tire length, cm	Engine capacity, cubic meters cm	Weight, kg	price, rub.
Carver PSG-52-18	2400	0.325	45	52	6.2	4145
Huter BS-52	2800	0.325	50.5	52	7.5 kg (with chain and bar)	5740
CALIBER BP-2800/18U	2800	3/8	45	58	6.2	4999
KRUGER GCSK 35-45	3300	0.325	45	52	6	8700
STIHL MS 180-14	1500	3/8	40	31.8	3.9	12990
Husqvarna 135	1500	3/8	40	40.9	4.4	13990
Makita EA3202S-40	1350	3/8	40	32	4.1	10340
Husqvarna 450e	2400	0.325	50	50.2	5.1 kg (without bar and chain)	21490
STIHL MS 250	2300	3/8	45	45.4	4.6	21990
Makita EA3203S-40	1350	3/8	40	32	4.1	13240
STIHL MS 880-36	6400	0.404	91	121.6	10 kg (without fuel, tire and chain)	94990
Husqvarna 395XP	5200	3/8	90	93.6	8.1 kg (without sawing apparatus)	60990
STIHL GS 461	4300	3/8	40	76.5	7.6	114990

back to menu ↑

Range of tasks for a chainsaw for a summer residence

Before you start choosing any tool, you need to consider the scope of its application. The required characteristics of the device will depend on the severity and duration of work on the site.

In the case of a country farm, there are several main functions that an automatic saw should perform:

1. Garden cultivation . This includes cutting down old branches, forming a crown, cutting off unnecessary shoots that pruners and loppers do not take. These events are seasonal in nature, that is, they occur mainly in spring and autumn.
2. Country construction . Once there is a plot, then there are ancillary buildings on it: a garage, sheds, a summer kitchen and much more. If the site has been developed recently, then all these facilities are yet to be built. With the growth of material well-being, the owner may wish to acquire a bathhouse or gazebo, a summer canopy for relaxation or a barbecue area. All these buildings are usually made of wood, where without a good automatic saw you would be without hands.
3. Preparation of firewood . In many private homes, stove heating is present as the main or additional heating. And if you don’t need much fuel to light an atmospheric fireplace during the holidays, a powerful wood-burning stove requires a large amount of work during the heating season to saw and split trunks and logs. In wooded regions, it is cheaper to order uncut firewood, but then this work falls on the owner of the house. Armed with a good chainsaw, he is able to cope with this task quickly and even with pleasure.