How to change the rubber seal on an Indesit refrigerator yourself

How can you tell if there is a problem with the seal in your refrigerator?

The first sign of problems with the rubber seal is the refrigerator door not closing tightly. If you doubt the presence of gaps in the seal, check it using a simple experiment. To do this, you will need a long strip of paper 4-5 cm wide. It must be placed perpendicular to the refrigerator door and closed. If the elastic band is not damaged, then you will not be able to pull the paper out of the closed refrigerator. The falling out of the paper is a sign of the presence of a gap through which warm air enters the refrigerator. To identify the presence of gaps, you need to “walk” such a probe along the entire perimeter of the door.

In addition, indirect indicators of problems with the seal are:

• Constant operation of the refrigerator without shutting down. The entry of warm air into the refrigerator or freezer through the gap formed between the door and the refrigerator body “forces” the compressor to work longer and more actively to create and maintain the set temperature.
• Increased temperature in the refrigerator. This occurs due to warm air entering it. The motor-compressor physically “cannot” cool the air to the required temperature.
• Ice formation on the back wall due to warm air entering the refrigerator. If the refrigerator is single-compartment, heavy ice will also form around the freezer compartment.
• Presence of a snow coat and leakage from the refrigerator. The ice that has grown on the walls of the unit melts due to warm air entering the refrigerator through the gaps between the housing and the damaged seal. As a result of defrosting, water appears under the lower drawers. As it accumulates, it can flow out of the refrigerator chamber along the front of the refrigerator or flow into the drain pan. But since the pan is not designed to hold a large amount of water, it ends up on the floor and a puddle may be visible on the floor under the unit.

It is important to understand that damage to the rubber seal on the refrigerator door is not a trifle, but a breakdown that can greatly affect the operation of the entire unit and lead to more serious troubles.

In what cases is replacement necessary?

It is not always possible to immediately notice a change in the microclimate inside the unit. In order to promptly detect the problem in the future, it is recommended to learn more about in what cases the rubber seal in the refrigerator is replaced:

• manufacturing defects: defects may not be visible to the naked eye, however, during operation there is an increase in temperature in the chamber, which will soon lead to premature spoilage of products, but more often the rubber gasket has significant flaws (loose fit to the refrigerator door, uneven width, etc.);
• cracks have appeared on the surface of the rubber seal, which may mean a loss of elasticity of the material and, as a result, a decrease in its functionality;
• the Atlant, Indesit, Ariston refrigerator or a unit of another brand is constantly running, while it hums, helping to cool the chamber, because cold air leaks, which causes a change in the microclimate inside the device;
• there is always ice on the back wall of the unit, it does not have time to melt, but based on this sign, a breakdown can only be assumed in drip-type models or analogues with the No Frost system;
• Considering that the refrigerator operates continuously, producing ice, some of it melts, as a result, the liquid does not have time to drain through a special hole, but flows down to the bottom shelf or bottom of the chamber;
• The door freezes on the inside, which prevents the refrigerator from being closed tightly; as a result, the problem gets even worse, which means you need to immediately replace the rubber band.

Due to the continuous operation of the unit, the engine begins to function intensively. This leads to its overheating and faster wear. Sometimes the problem of insufficient sealing of the elastic material causes engine failure, which can be found out after the repair if the rubber on the door is not changed in time.

Possible consequences of a malfunction

Violation of the tightness of the unit housing in the closed position can lead to a number of problems:

• the motor is constantly running, while the hum, which should be heard only periodically, is not interrupted, as a result, energy consumption increases, since the required temperature is not maintained inside;
• Ice freezes on the walls and doors;
• a lot of water accumulates inside, which is a consequence of the thawing of ice;
• products do not last long;
• the temperature sensor breaks down, this happens as a result of constantly turning the unit on and off, because the temperature inside is not low enough, when the refrigerator turns on, the microclimate temporarily normalizes, but soon the temperature regime changes again, which will require constant operation of the sensor;
• The engine fails if the seal in the refrigerator Stinol, Ariston, etc. was not replaced in time.

What damage does it prevent?

Over time, dents and gaps form on the rubber, and it loses its elasticity. A thinned seal can cause major repairs to the refrigerator. After all, the manufacturer calculates the power of the device under certain operating conditions. Forced to work in extreme mode, the device may simply not withstand the load. Therefore, such a seemingly insignificant detail should under no circumstances be neglected. It turns out that the refrigerator operates around the clock at full capacity. This reduces its service life.

Signs of seal failure

You can understand that the sealing rubber in the refrigerator needs to be replaced with the naked eye. Over time, it dries out, becomes less elastic, and cracks. This is due to the temperature difference between the refrigerator compartment and the kitchen, as well as purely mechanical damage due to regular use.

But even if, at first glance, such signs of failure of the rubber seal are not yet visible, but cold air is clearly blowing from the door, and ice freezes heavily on the inner walls, then repair work is also necessary. Otherwise, more and more warm air will get inside, which the device will need to cool, which will ultimately lead to overloads and breakdowns of the motor, as well as excessive energy consumption.

Why does the seal in the refrigerator wear out?

Seal that requires replacement
You can tell that it’s time to replace the old tape with a new one by the ice that forms on the freezer door. Due to the fact that warm air gets inside, the temperature in the refrigerator will not be low enough. Over time, in older models that are used for a long time, the elastic band dries out, cracks and becomes less elastic. The tape may become unusable if the equipment is handled carelessly. The reason that the rubber band will have to be changed may be sagging of the door due to its own weight, as well as a malfunction of the sensor that is responsible for opening it. In case of partial or complete wear, you need to replace the rubber bands on the refrigerator door.

The rubber seal is a simple and rather weak part. It performs an important task, ensuring tightness. When the belt is deformed and destroyed, this immediately affects the operation of the unit. Cold air flows out, while warm air flows in. All systems are overloaded.

If the seal is slightly damaged, it can be repaired. A test will help you decide. A flashlight is placed inside the refrigerator. If the seal is poor, light will show between the seal and the housing. This means there are gaps.

They check it in another way. To do this, take a sheet of paper. Bring it to the body and close the door tightly. They pull on the peeking edge. If the paper is easily pulled out, then the seal must be replaced. They also check the places at the bottom and top of the door. The elastic band should fit snugly along its entire length. The fact that the tightness is broken can be judged by the following on it:

• dents;
• chipped;
• cracks;
• bends.

Are you here

Video instructions for replacing the seal on the refrigerator Stinol 101 (Stinol 101)
I. Instructions for replacing seals of the profile type “under the bar” - profile type IN, AM for refrigerators with doors in which the seal is glued to polyurethane foam - polyurethane foam (Stinol, Indesit, Ariston, Liebherr, etc.).

When dismantling the old seal and installing a new one, our technicians do not turn off the refrigerator, because Replacing the seal takes no more than 30 minutes for the 1st refrigerator compartment.

Unloading products and removing the door from its hinges is also required in rare cases.

Required tools: screwdriver - 2 pcs, hair dryer or household hair dryer, screws for fastening, screwdriver, dish sponge and detergent.

The essence of the process.

The seal is glued onto the polyurethane foam by the manufacturer and visually looks like it is permanent

— Before dismantling (removing) the old seal, it is necessary to widen the hole into which the seal is inserted to facilitate the removal process.

— We install a new seal to replace the old one and fasten it with self-tapping screws (by analogy with the old refrigerators “Biryusa”, “Polyus”, etc.)

A) adjust the door height when sagging (wear of bushings) using washers of a suitable internal diameter, putting them on the door mounting rod.

B) adjust the door when the seal is jammed on the hinge side, placing washers under the hinge fastening bolts.

C) if the seal does not fit tightly, warm it up with a technical or industrial hair dryer at a temperature of the outgoing air flow of 200 - 250 °C.

Step-by-step instruction:

• Open the refrigerator door.
• Unscrew the seal and insert a flathead screwdriver between the seal and the plastic casing of the refrigerator body.
• Run a screwdriver along the seal along the entire height of the door, thereby widening the hole to make it easier to remove the seal
• If necessary, do the same on the other side of the seal (by inserting a screwdriver between the seal and the metal body of the refrigerator door trim
• When removing the seal, make sure to remove it entirely as Remaining sealant may interfere with the installation of a new seal.
• Remove the old seal around the entire perimeter of the door
• Insert the new seal, starting from the corners and gradually tucking the “tail” under the plastic casing, widening the hole with a screwdriver.
• Level the seal around the entire perimeter of the door and adjust at the corners
• To facilitate the fastening process, we suggest using a cordless screwdriver and self-tapping screws with a hemispherical head with a press washer diameter = 4.2 mm and length = 16 mm (with a “drill” tip).
• Fixation with self-tapping screws is carried out starting from the corner and every 10 - 15 cm (more often if necessary)
• Next, if required, the door (hinges) are adjusted and the seal is heated.

If the seal is attached to self-tapping screws (screws)

Video instructions for replacing the seal on the Nord 233 refrigerator (NORD 233)

link to video https://www.youtube.com/embed/JcEJ0m-Sqzw?rel=0

Video instructions for replacing the seal on the Snaige refrigerator (Soviet)

link to video www.youtube.com/embed/cZq-3TUwlKM?rel=0

Any other information can be obtained from our managers by calling 8-800-200-85-60.

II. Instructions for replacing seals of the “in-groove” profile type - profile type OM, LG, etc.

for refrigerators with doors in which the seal is inserted into a groove

How to check the tightness of the refrigerator yourself

First Step to Troubleshooting Your Refrigerator: If your refrigerator light is on and you can hear it running but the appliance won't stop, make sure there is nothing blocking the passage between the freezer and refrigerator compartments. If, for example, a loaf of bread shoved in front of the aisle restricts the air flow, the refrigerator will not cool down. Therefore, it will continue to work in an attempt to reach the set temperature. If your refrigerator is running non-stop, its refrigerant may be low. A refrigerator with low refrigerant content cannot reach the low temperature setting of the cold control dial. You will need a refrigerator repair technician to check and/or increase the refrigerant levels.

Open the door. If you feel a draft, make sure there is a problem with the seal. In some cases, this is not the cause of such a malfunction, for example, a blocked anti-frost drain is to blame. The defrost drain is usually located on the back wall of the freezer, just above the slope from the floor to the back wall. A buildup of food particles or debris can clog the drain hose, causing ice to build up and water to leak from the freezer and refrigerator. To fix this, try drying the hole from the inside using warm water. Use a long, thin tool, such as a drain cleaner, to remove the clog.

If this doesn't finish the job, you may have to manually remove the buildup that is clogging the valve at the end of the drain hose. Locate the defrost drain hose at the back of the service panel by moving the refrigerator away from the wall. This hose should have a rubber valve that helps catch debris and prevent clogging. Wash the valve with hot water and soap, and then replace it.

DIY repair

If the rubber band is deformed in one or more places and the door comes off, allowing warm air into the refrigerator compartment, repairs can be made. To do this, you will need a hair dryer with a hot stream of air or boiling water.

In the first case, you can use a hairdryer to repair one small damage to the seal. To do this, this place is heated with a hot stream of air and, when the elastic becomes elastic, it is given the desired shape. After this, you can glue it in place or attach it to the Atlant refrigerator door with screws.

If the elastic band is deformed in several places, it is completely removed and placed in a bowl of boiled hot water. After it becomes elastic, wipe the elastic band dry, give it the desired shape and attach it to the door of the Atlant refrigerator.

When is it time to change rubber bands?

Signs that the refrigerator door seal requires replacement:

• The device began to work unacceptably long and often, reminding of itself with the sound of a working compressor.
• A large layer of frozen ice and snow appears in the refrigerator compartment.
• Gaps have formed between the unit body and the rubber band.
• A visual inspection revealed damage to the sealing rubber (cracks, holes and other defects).

In the first two cases, it is necessary to check whether the elastic band fits tightly to the body; even if the cracks are not visible “by eye,” this does not mean that they do not exist. To check the gap, you must use a special feeler gauge no more than 0.1 mm thick or use a piece of paper 2-3 cm wide. When the door is closed, the feeler gauge should be pressed tightly with the seal around the entire perimeter of the door. If this does not happen, then you should replace the rubber seal on the refrigerator so as not to aggravate the situation. Ignoring problems with the seal, in addition to deteriorating the quality of the unit’s operation, will ultimately lead to failure of the compressor and other important parts.

Preparing for work

To change the rubber, you must first remove the old seal and clean the installation site. It should not be a too aggressive solvent; it is quite enough to use an alcohol solution for acrylic paints.

Replacing refrigerator door rubber

Using acetone, you can remove any remaining adhesive that is attached to the refrigerator and does not come off along with the old sealing gum. However, acetone is too aggressive a solution, so it is used spot-on and is not suitable for final cleaning.

How to choose a seal

When choosing a seal, pay attention to the type of fastening that secures the rubber to the door and the size of the door itself. You also need to know the brand of your unit, this will help you avoid awkward moments and more accurately select the required spare part.

Depending on the type of fastening, these parts can be: glued with glue or polyurethane foam, screwed with self-tapping screws, or held in place by fastening in grooves. When purchasing a new product, consult with a sales consultant and, if necessary, purchase additional elements (screws, glue, etc.).

Let's look at the process of replacing rubber seals on different brands of refrigerators.

Finished door frame

Stinol, Snaige, Atlant and Nord

To repair the unit we will need: two flat screwdrivers, screws with a press washer, a screwdriver and a hair dryer. If necessary, the door must be removed; if there is easy access to the repair object, then you can leave it in a vertical position. To remove the old rubber, insert a screwdriver between the seal and the plastic and separate them, then separate the seal from the door in the same way, tearing off the mounting foam connecting them.

Carry out this operation along the entire length of the seal and release the elastic from the grooves. Afterwards, clean the space from any remaining foam or glue and carefully look to see if there are any pieces of the old seal left there that will interfere with the installation of the new part.

After removal and cleaning, you can begin installing a new seal. When handling the seal, extreme care should be taken to avoid damaging the product. Installation should begin from the corners of the doors. Increase the gap between the plastic and the door by inserting 2 screwdrivers between them on different sides of the corner, 15-20 cm from the corner. Insert the seal into the groove and secure it there. Repeat this with other corners. Then, using 2 screwdrivers, insert the rest of the sealing rubber into the grooves. It should be noted that during factory assembly this part is fixed very tightly, which is problematic to achieve in everyday conditions.

For a tighter fit of the rubber to the door body, you should screw the plastic to the door with screws every 15-20 cm, thereby clamping the seal between them. To ensure the tightest fit of the seal to the body of the Stinol refrigerator, it is necessary to heat the rubber band with a technical hairdryer at a temperature of about 300 degrees, and then allow it to cool by closing the door.

Types of seal fastening in Indesit refrigerators

• Fixation with glue (the polymer base of the glue is susceptible to low temperatures and wears out quickly).
• Shrinkage into a groove (the door has a special channel around the perimeter into which the seal is seated).
• Fixation with screws.

Reasons for wear of sealing rubber:

• Mechanical damage (scratches, tears).
• Temperature fluctuations (leads to stretching of the seal and the formation of cracks).

Changing the seal of the Atlant refrigerator with your own hands

• When installing a new seal, it is best to use the same method in which the old one was attached.
• If you decide to use glue, degrease all surfaces involved in the process. Use only high-quality and proven adhesive.
• If you decide to screw on the seal, use wider screws than were previously used, as the holes should have expanded over the years.
• When inserting the seal into the groove, use glue to secure it more securely.
• Once you are sure that the seal is securely fastened, you can turn on the refrigerator and use it as usual.

Replacing the seal

To replace the factory rubber seal, you must follow the step-by-step instructions.

Dismantling the old

Dismantling (i.e. replacing with a new one, repairing or re-hanging on the other side) is necessary when the gasket no longer fits tightly to the body. This can happen when the hinges become loose, cracks appear in the body, or the door leaf is damaged. It is carried out in several operations:

1. Defrosting (if you need to repair an old refrigerator) or disconnecting the device from the power supply (if the equipment is of the latest generation). You must first remove the contents from the chambers.
2. The refrigerator is placed on its side, with the hinges facing up, otherwise the panel will be inconvenient to remove.
3. The hinges are unscrewed (starting from the bottom), after which the structure is carefully pulled out of the grooves.
4. The sealing gum and fabric are checked for damage. If cracks, rot, old blockages in the cracks or severe deformation of the case are detected, the part must be replaced with a new one, otherwise this may lead to damage to the device or damage to the products.
5. If the parts are not damaged, then the canvas is cleaned of dirt, and the gasket is glued back in the right places. If its material begins to mold or loses its elasticity and volume, then the elastic band needs to be replaced.
6. After this, the door is installed back.

Surface preparation

To subsequently replace the sealing rubber, remove all remaining adhesive and clean the surface of debris and dust. You will need a rag and a medium strength solvent. Acetone is useful for removing glue, but for final cleaning it is too strong. Solvent for oil paints is too greasy and will not give the desired effect.

An excellent option would be an alcohol-based acrylic paint solvent or white spirit. If you choose to repair rather than replace, you will also need a good solvent.

Installing a seal on the refrigerator door

You need to choose the mounting method that was used previously. If the previous seal was inserted into the grooves, then attach the new one in the same way. Except in cases where, for example, the elements of the refrigerator door are broken.

Important: in production, the seal is attached to the groove using special equipment, so it is impossible to repeat this yourself manually. It is recommended to additionally secure the seal with glue or self-tapping screws. Depending on the situation, you will need to use one of the installation methods. The main thing is to do the work carefully and follow the order of the steps.

The following options can be used:

• - glue it. The most important thing is to clean and degrease the surfaces with a solvent. According to the instructions on the package, the glue must be applied and dried. Do not close the refrigerator door until the mixture is completely dry.
• - screw it with self-tapping screws. If the refrigerator is old, then most likely the fasteners are loose and the seal does not hold well. Attach the new tape to the self-tapping screws.
• - insert into the grooves. The herringbone seal must be inserted into the slots and additionally secured with screws or glue. The screws need to be screwed in at a distance of 10-15 cm from each other.

When the work is completed, you need to carefully inspect the installed sealing rubber to make sure that the tape was not damaged during the installation process. If the installation was carried out correctly, then opening the refrigerator door requires some effort. You can do the test again with a piece of paper.

Important: dirt accumulates in the grooves of the seal; they need to be cleaned, and the surface should be treated with disinfectants without abrasive particles in the composition and without acids.

Removal and installation of the refrigerator seal

Watch this video on YouTube

Removing remaining glue

You can remove the remnants of the adhesive solution on which the seal was held using acetone. Apply the product to pieces of dried glue, wait 5-10 minutes, then treat with a spatula. The final cleaning is carried out with an alcohol solvent intended for acrylic paints.

How to replace

To work you will need:

• the seal itself;
• spatula (to remove old glue);
• self-tapping screws, if it was decided to fix the elastic strip mechanically;
• hot water, hair dryer.

You can change the seal on an Indesit, Ardo or other brand refrigerator at any time, which means you first need to try to remove the defect using a heat source. To do this, use hot water or a hair dryer. The last option helps to remove small irregularities that cause cracks to form. To implement it, it is necessary to heat the deformed area with a construction hairdryer. Then use your hands to give the polymer material the desired shape and press the door against the body of the refrigerator. When the strip cools, it will level out.

Significant defects can be removed using hot water.

To do this, it is necessary to dismantle the seal. It is completely immersed in water. In this case, the polymer material is heated, which allows it to change its shape. Then it is installed in place. However, in this case there is a risk of more severe damage to the strip, since in a heated state it can be deformed in other places. It is important to spread the material over its entire length.

Removing the old seal

Replacement of the refrigerator door rubber is carried out after the unit has been disconnected from the voltage source. It is recommended to carry out work when the chamber is empty. If ice is frozen on the door, you need to wait until it melts. It is better to carry out work in a horizontal plane. To do this, you need to remove the door from its hinges. If this is not possible, you will have to perform installation in a vertical plane. In this case, there is a risk of a decrease in the quality of the installation.

Once the seal is secured in the groove, no tools are required to remove it. It is enough to bend the strip with your finger and pull its upper part towards you. In most cases, the seal is quite easily released from the groove. However, due to prolonged use, it could stick to the surface of the door. Then use a screwdriver. It must be positioned perpendicular to the seal. The screwdriver should be between the edge of the panel and the elastic strip. This will allow you to pick up the seal and quickly pull it out by hand.

If the elastic material is fixed to the surface of the panel using self-tapping screws, use a screwdriver for dismantling. When the seal is attached with glue, it is necessary not only to remove the strip, but also to ensure that the surface where it was located is clean. Remove any remaining adhesive and pieces of polymer material. This will ensure a snug fit of the strip.

Installation

The seal is placed in the same area where the old elastic tape was located. To do this, use a screwdriver, but it is better to do everything with your fingers without using a tool, since in this case the risk of damage to the material increases. The seal is tucked into the groove on the side where the herringbone mount is located. It is necessary to straighten the strip over the entire width.

If it is not possible to find a suitable product, replacing the seal in the refrigerator Stinol, Ariston and units of other brands is carried out using a product of a different type, but using self-tapping screws and glue.

When fasteners are used, it should be borne in mind that in this case it is not always possible to ensure the tightness of the structure. The recommended spacing of screws when installing the seal is no more than 15 cm. If you plan to use glue, you must first degrease the surface in the area where the composition will be applied. This measure will help increase the adhesion of materials.

Why replacement rather than repair?

Replacing the rubber seal in the refrigerator is a more preferable procedure than repairing it. Because it will give a long-term effect and is a cost-effective and practical solution. So, what needs to be done to change the material yourself and not involve specialists in this procedure? Half the success depends on choosing the right sealing rubber. It is ideal if you find a “native” seal designed specifically for your refrigerator model. In this case, replacement is made as simply and quickly as possible - just fix the rubber band on the doors. If you were unable to find a similar sealant and you purchased a universal material, you will have to spend a little time taking measurements, trimming and gluing the sealant. The following situation may also arise: you bought a seal suitable for your refrigerator model, but for some reason it does not fit well onto the doors. Don’t rush to get nervous - just heat the material with a hair dryer at maximum temperatures. Thanks to this, it will become more pliable, and you will be able to carry out the desired procedure without any problems.

Choosing a new seal for the Atlant refrigerator

When choosing new tires, make sure that there is no damage to them. Try to find a seal designed specifically for your refrigerator. If this is not possible, use seals that fit your size. As an example, you can use old rubber, but you need to take into account that over the years of use it has become compacted, and the new seal must be wider. If the material you purchased is too large, you can cut it to fit the desired size.

Can it be repaired?

The elastic material is secured in the door groove securely enough to provide a tight seal. But this does not prevent us from dismantling this strip on our own. If possible, it is better to contact specialists. However, such work can be performed even without much experience.

You can change the rubber seal on the refrigerator yourself if you know the model of the unit. The cross-sectional configuration of this strip differs depending on the brand of the device. There is a groove for inserting it. The principle of location of the rubber strip is different. The shape, as well as the size of the groove, can also vary. For this reason, you should repair the refrigerator seal yourself if you can find an elastic material that matches the parameters of the old strip.

There are universal tapes. They can be used to replace the old rubber on the unit door. However, such products differ in their significant width. To install it on a refrigerator, you must first determine the dimensions of the seal. The key parameters are the following: width and length. Then, if necessary, the excess strip is cut off, after which it is fixed in the groove.

The sealing rubber can be replaced completely or partially. Preference should be given to the first method. This is due to the fact that in this case there are no leaks around the perimeter of the door. The elastic band runs in a continuous stripe. If you replace only partially, gaps may appear between sections of the seal.

It is not possible to change the rubber on the door yourself in the latest models of equipment.

In this case, the unit may be under warranty, which means that the defects are eliminated at the service center. You cannot dismantle the strip yourself. The difficulty of replacing the seal in new models of units is due to the fact that sometimes it is located under the door lining layer. Then it is impossible to remove the rubber yourself; knowledge and special tools are required. Otherwise, the lining of the unit will be damaged, which may reduce the attractiveness of the equipment.

✅CHECKED! STINOL - replacing the seal on the refrigerator door

Watch this video on YouTube

replacing the seal in the refrigerator

Watch this video on YouTube

Replacing the refrigerator door seal Indesit Stinol Atlant

Watch this video on YouTube

Indesit

Replacing the seal in Indesit brand refrigerators is done by analogy with refrigerators Stinol, Snaige, Atlant and Nord. We will also need 2 flat screwdrivers, a screwdriver, screws with a press washer and a hair dryer. If the refrigerator is single-chamber, the door must be removed for ease of repair; if it is a two-chamber refrigerator, you can carry out repairs without removing the door from the unit.

The seals on the Indesit brand unit are also attached to mounting foam or glue, which is torn off using screwdrivers and the old rubber is removed. By analogy, fastening a new part begins from the corners and after installing the rubber in the grooves, it is secured with screws and heated with a hairdryer. The original rubber seal for the Indesit refrigerator is best suited, but if this is not possible, you can replace it with a suitable size. The same applies to other brands Snaige, Atlant and Nord.

ZIL brand units have one characteristic difference among the others: the rounded upper part of the door, which plays an important role when replacing the seal. To replace the old version of the seal, ZIL brand units now use products with a magnetic insert, which ensures good tightness.

Units of this brand are produced with doors of two sizes; pay attention to this when choosing a seal. The process of removal and installation is similar to manipulations with other units, but during installation the rubber must be divided into two parts, one part will cover the bottom edge of the door, and the second will cover the entire remaining perimeter.

Restoring the rubber seal on an Indesit refrigerator

If the rubber seal on the refrigerator door is slightly deformed, it can be restored. The refrigerator must be in a horizontal position, standing level and not skewed. First, the seal must be cleaned with ammonia to remove dirt, dust, and other things.

Ammonia cleanses grease, dirt and makes the rubber seal flexible.

Now you need to find the place where the seal is deformed, for which we take a regular sheet of paper and press it with the refrigerator door, where the sheet is movable, this place is damaged. If the deformation is no more than two millimeters, then you can put a material under the seal itself that will fit in size.

• You can heat the rubber band with a hairdryer up to seventy degrees, after which you need to give the seal the desired shape and glue it to the door of your refrigerator;
• You can also use hot water, but in this method it is necessary to pour boiling water over the seal before heating the gum, then give it the desired shape;

Another more complex method is to use a steam iron.

You can also check for leaks using a flashlight. The flashlight must be placed in the refrigerator, then checked around the perimeter of the door for gaps.

Using boiling water

First, remove the rubber band from the refrigerator door. This process can be quite difficult. More precisely, there can be 2 ways:

Modern refrigerator manufacturers attach this part to foam, in which case it will be easy to remove. In Soviet units, the elastic band is screwed on with nails; it is quite difficult to remove it

Therefore, you should remove it very carefully so as not to deform it. Otherwise, you will have to buy a new one.

So, let's move on to the actual processing of the material. Everything is extremely simple. You just need to scald it with boiling water and leave it in hot water until it cools completely. This way you can restore the rubber band on the refrigerator.

Dry it well and hang it back. After this treatment, the part will begin to fit tightly to the door and its tightness will not be compromised.

How to restore the rubber seal on a refrigerator

If the rubber seal on the refrigerator door is slightly deformed, it can be restored. The refrigerator must be in a horizontal position, standing level and not skewed. First, the seal must be cleaned with ammonia to remove dirt, dust, and other things.

Ammonia cleanses grease, dirt and makes the rubber seal flexible.

Now you need to find the place where the seal is deformed, for which we take a regular sheet of paper and press it with the refrigerator door, where the sheet is movable, this place is damaged. If the deformation is no more than two millimeters, then you can put a material under the seal itself that will fit in size.

Restoration of sealing gum using the hot method:

• You can heat the rubber band with a hairdryer up to seventy degrees, after which you need to give the seal the desired shape and glue it to the door of your refrigerator;
• You can also use hot water, but in this method it is necessary to pour boiling water over the seal before heating the gum, then give it the desired shape;
• Another more complex method is to use a steam iron.

You can also check for leaks using a flashlight. The flashlight must be placed in the refrigerator, then checked around the perimeter of the door for gaps.

How to glue a rubber band in the refrigerator

To begin replacing the rubber seal on the refrigerator door, you need to treat the door surface with a mild solvent. The best solvent option for these purposes is alcohol solvent for acrylic paint.

To replace the sealing rubber, it is imperative to use the same fastening method that was used to fasten the old material.

The rubber seal can be fixed using glue or a screw.

Attaching the rubber seal for the refrigerator can be like this:

1. Screw fastening. For this method, you need to try on the rubber seal on the refrigerator door and if it fits tightly and does not give you any doubt that it will perfectly preserve the tightness of your refrigerator, simply tighten the fasteners.
2. Fixing the seal with glue. After trying on the new seal on the refrigerator door, you need to apply a thin layer of glue around the perimeter of the door and attach the prepared rubber band.

The glue you need to choose is silicone-based and of very high quality; if you buy a low-quality glue or a cheap fake, you will soon need to replace the seal again. Turning on and using the refrigerator is permitted only after the glue has completely dried.

Let the seal sit for a while

After purchasing the material, do not rush to immediately begin replacing it. Here it is very important to let him rest for at least a day. The new rubber must reach the desired temperature, straighten, and acquire the appropriate moisture content. For greater reliability, experts recommend keeping the material in warm water for a while before replacing the seal in the refrigerator.

Using paper or other available materials

This method will only work if the deviation from the door does not exceed 2 mm

Therefore, first you should measure these discharges (this is important)

After this, you can take a piece of paper, cardboard or other similar materials and place it under the place where the elastic comes off.

How to change the seal on a Stinol and Indesit refrigerator with your own hands

To replace the sealing rubber on refrigerators: Indesit or Stinol, you will need a flat screwdriver, since on such models of refrigerators the rubber seal is secured with screws.

The seat of the seal is quite deep; during the manufacture of the refrigerator, the door seal is attached until they are installed on the unit. And therefore, without dismantling the door, you will not achieve the same tightness as with factory fasteners; it is recommended to use self-tapping screws with a press washer.

Recommendations on how to properly remove the seal and attach a new one in Indesit and Stinol refrigeration units:

• We disconnect the refrigerator from the network; if the size of the refrigerator door is large, then it is recommended to remove it from its hinges and lay it horizontally, and if the door is not large, then the replacement can be done in a vertical position;
• We pull back the edge of the rubber band, insert a flat-head screwdriver into the gap between the seal and the door and use the screwdriver to tear the mounting foam that secures the seal;
• We take out the rubber from the groove around the perimeter of the door, try not to tear it;
• It is almost impossible to find a seal that is intended for repairing refrigerators of the Indesit and Stinol brands, so they use similar seals;
• It may be necessary to strip the groove;
• We stretch the purchased seal along the perimeter of the refrigerator doors, begin to fasten it from the corners: insert a flat screwdriver between the plastic and metal of the door and place an elastic band in this groove;
• We insert the seal along the entire refrigerator door;
• We pull back the edge of the rubber seal a little and screw the screws into the plastic at intervals of ten or fifteen centimeters;
• Next, we warm everything up with a hair dryer to about three hundred degrees;
• If the rubber band is properly attached, the refrigerator door will open with little effort.

You can repair Ariston or Atlant refrigerators if your rubber band has burst or torn, using the same method. It all depends on the level of breakage of the rubber bands; if it is slightly torn, then the seal can be softened, sealed, or a gasket can be installed. Next, everything needs to be lubricated and put in place. If repair or sealing fails, the tires will have to be replaced. How to install everything correctly was described above, and you can also familiarize yourself with the workflow in a special video.

In extreme cases, rubber for sealing can be collected from parts. The method of fastening is the same, but to ensure tightness, we coat all the joints between these pieces with glue and cover them with adhesive tape. Outdated models of refrigerators are most often exposed to this method.

Why won't the door close

The refrigerator door may not close due to various malfunctions. To eliminate the problem, it is necessary to conduct an inspection and determine the specific cause.

Loosening and deformation of fastenings

If the fasteners are deformed from mechanical stress or become loose as a result of prolonged use, the door no longer fits tightly. If the fastenings become loose, adjustments can be made. To restore deformed elements, professional repair or replacement of parts is required.

Rotten, loose and cracked seal

Due to the detachment of the seal or a violation of the integrity and structure, it cannot fulfill its purpose and does not secure the door. A broken seal is easiest to replace with a new one, which will reduce labor and time costs.

Complete replacement

To completely change the seal on the Atlant refrigerator, you need to remove the door and lay it on a flat surface. After this, all the old rubber is removed and the installation site is thoroughly cleaned. Then the new seal is stretched and installed in the grooves. After this, you can glue it or replace the old screws with new ones by screwing it with a screwdriver.

Refrigerator door rubber

Changing tires yourself is not difficult. The main thing is to have a minimum set of working tools and the desire to do the work yourself. Otherwise, it is not difficult and does not require special skills.

Tips and tricks

If the damage is minor, the seal can be repaired. Places of slight deformation are blown with a hair dryer or for drying hair (the hottest mode), change the shape of the elastic with your fingers and firmly press the door, fix it in this position for 10–15 minutes. Another option for restoring the seal is to remove it and immerse it in hot water, leave it for 15 minutes, when the part takes the desired shape it can be put back. Places where the tape has moved slightly away from the door can simply be glued, and small cracks can be sealed with sealant.

On a note!

If the tape is damaged only on the outside, it can be removed, turned over and reattached. Such a replacement of rubber on a refrigerator cannot be carried out if it was glued.

In order for the seal to last as long as possible, the door must be opened only by the handles or special recesses, without touching the rubber bands. When washing the refrigerator, all grooves in the tape should be cleaned with a toothbrush and soda paste. After replacing and drying the rubber, it must be treated with silicone grease; oils cannot be used, they make the material inelastic.

It is permissible to attach the new type of seals with double-sided tape (on the latest models of refrigerators), but no one can say exactly how long the part will last. Experts do not recommend using polyurethane foam to glue the part. For any mounting method, the tape must not be stretched. You need to measure the elastic from the upper corners (length and width).

Installation of sealing tape is not a complex type of repair, but requires attention and accuracy. You need to choose the right part, carefully remove the remains of the old gum and prepare the surface before work. By following our advice, you can change or repair the rubber seal in the refrigerator yourself, without using the services of service centers; the procedure will not take much time.

Sources

• https://rembitteh.ru/hozyayke-na-zametku/zamena-uplotnitelya-holodilnika/
• https://trg-market.ru/tehnika/zamena-uplotnitelnoj-rezinki-na-holodilnike-indezit.html
• https://NiceDeck.ru/delimsya-opytom/zamena-rezinki-na-dveri-holodilnika.html
• https://vemiru.ru/info/zamena-uplotnitelja-holodilnika-indezit-svoimi/
• https://remont-indesit.su/neispravnosti-indesit/neispravnosti-holodilnikov/15-remont-zamena-uplotnitelya.html
• https://vph-holod.ru/remont/kak-pomenyat-uplotnitel-na-holodilnike-indezit.html
• https://kakchistim.ru/tehnika/stiralnaya-mashina-tehnika/kak-samostoyatelno-pomenyat-uplotnitelnuyu-rezinku-na-xolodilnike.html
• https://WyseDevice.ru/kuhnya/kak-pomenyat-rezinku-na-holodilnike-indezit.html
• https://expluataciya-holodilnika.ru/holodilniki/marki/indesit/ustanovka-uplotnitelnoj-rezinki-na-holodilnike-indesit/

Do you want to understand better than others?

• How to change a light bulb in an Indesit refrigerator - Replacing a light bulb in an Indesit refrigerator: step-by-step instructions Step 1. First, you need to disconnect the refrigerator from the power supply. In addition, you will need to get all the products out of it and...
• Replacing a light bulb in a refrigerator - It would seem that the presence of a light bulb in a household refrigerator does not in any way affect the storage of food. But its absence causes a lot of inconvenience. Especially in the dark. IN…
• Replacing the compressor of the INDESIT refrigerator. Typical refrigerator problems and their solutions - Signs indicating a compressor malfunction The main “symptom” is warming in one (applies to two-compressor models) or in two chambers. Temperature gradually...
• Why is the fan in the Indesit refrigerator noisy or humming - Why is a fan needed? The system is based on a cooling chamber, the design of which has three main elements: an evaporator; cooler; heater. Impeller…
• Installing a rubber seal in a refrigerator - A rubber seal for a refrigerator is a part that is inexpensive. But damage to it can eventually lead to engine failure. You can change the rubber...

Required Tools

You can seek the help of a professional to replace the sealing rubber if the new model has hidden grooves and you need to know the fastening diagram in order to remove the sealing rubber. This happens with the Atlant XM 6021-031 refrigerator model. In conventional models, such as KShD 256, there will be no problems with replacement. It is better and cheaper to do this work yourself. Changing the rubber band is quite simple; there are several ways to do this.

In addition, this work does not require a large set of tools:

• a piece of suitable sealant;
• fasteners (glue, screws, double-sided tape);
• a small spatula to remove excess glue;
• hairdryer or boiled water.

The installation diagram for the rubber seal for the Atlant refrigerator is quite simple and does not require any professional skills.

Removing the old seal

Replacing the sealing rubber on the refrigerator begins with removing the old rubber. To do this, the refrigerator is turned off, the food is removed, and the door itself can be removed for convenience, if the design allows it, and placed horizontally. The further dismantling procedure will differ slightly depending on how the sealing rubber is attached.

1. If the seal is attached to the door in a groove, its edge must be pulled back, a flat-head screwdriver inserted into the slot and, using it to pry up the material, pull it out of the groove, being careful not to tear it.
2. If the old seal is glued, it is also carefully pryed off around the entire perimeter with a screwdriver or spatula.
3. With screws it’s even easier - you just need to unscrew them.

Next, the surface must be cleaned of dust and debris with a damp cloth, and also wipe off all remaining glue, small adhered particles of the rubber itself, etc. The rough glue can be easily removed with acetone, but it is better to wipe the door clean with a solvent for acrylic paints or white spirit.