How_to_replace_the_light_bulb_in_the_ariston_hotpoint refrigerator

What kind of light bulbs are used in refrigerators?

A refrigerator is a single mechanism consisting of many components and parts. All of them are necessary and equally useful. The refrigerator light is no exception.

There are several types of lamps used in refrigerators:

• General purpose incandescent lamp: burns, emitting warm light, affordable, has a relatively short lifespan. It heats up during operation, and the service life is short - up to 1000 hours.
• Halogen: can be either cold or warm glow, economical, lasts longer.
• Luminescent: creates a bright, cold light, is less expensive, lasts up to 15,000 hours.
• LED: generates light in any color range, including colored tones. Does not heat up, insensitive to low temperatures, “eternal” lamp - its service life is over 100,000 hours (about 11 years of continuous operation in household refrigeration appliances).

The type of lamp does not affect the cost of the refrigerator, but it does affect the service life.

Often, refrigerators use lighting fixtures with a power of 15 W or 25 W. In large chambers, 2 light bulbs of the same power are installed, or one up to 40 W.

See also -

Why did the refrigerator become loud: causes of malfunction

Which ones are used?

Socles

There are several types of base used in the design of a refrigerator lighting element. Not every product may be suitable for your refrigerator model. The most common and frequently encountered bases are:

1. E14 (Atlant, Stinol (stinol), Indesit (indesit), Hotpoint Ariston (hotpoint ariston), Nord (Nord), Gorenje (burning)),
2. E12 (Liebherr, Samsung, Hansa, Bosch, Electrolux, Beko, Whirlpool).
3. E27.
4. Occasionally you can come across a type such as T-Click (Whirlpool, Atlantic) with 2 terminals or 2G7 with 4 terminals (Phillips, LG).

Technologies

Due to the rapid pace of development and modernization of household appliances, the lighting inside the refrigerator has been constantly updated and optimized. The following types of lamps are most often used in luminaires:

• Incandescent. The most uneconomical ones, installed in cheap models, produce warm yellow light, but get quite hot during operation. Will last for 1000 hours of operation. Among the disadvantages, it is worth noting the high sensitivity to voltage surges, which can lead to rapid failure.
• Halogen. They emit quite bright light. They do not heat up much and are not similar in design to incandescent light bulbs, but their energy efficiency is higher. Will remain operational for a period of up to 4 thousand hours.
• Light-emitting diode (LED). Eco-friendly, energy efficient, popular, practically do not heat up. The service life reaches 100 thousand hours.
• Daylight (fluorescent). Thanks to the white color, they allow you to clearly see the contents of the refrigerator compartment; the service life reaches 15 thousand hours. A significant disadvantage is the presence of mercury vapor: the disposal of this element is carried out by special companies.

An important factor is the power, which usually varies depending on the location and type of device in the range from 11 to 40 watts. Most models use 15 or 25 watt fixtures. In large-sized two-chamber equipment, several or one of them are installed, but at 40 watts.

Why do they burn out?

Reasons why lamps burn out:

• Low-quality cheap products produced by handicraft methods were used.
• End of service life. Each lighting element has a manufacturer-declared operating time in hours.
• High load. For example, voltage surges, frequent leaving the refrigerator door open, incorrectly selected type of lighting.

Why doesn't the light in the refrigerator light up?

If the lights go out unexpectedly, you may not need to replace the light fixture.

• Check the wiring, electrical outlet, power cord.
• Connect another household appliance, such as a table lamp or hair dryer, to the electrical outlet.
• If there are no problems with the power supply, observe the operation of the refrigerator itself. Natural shutdown lasts up to 30 minutes; if it is silent longer, the problem is in the transformer.
• It's possible that the light hasn't been lighting correctly lately (the light has been flickering, turning off, and then coming back on). Check the cartridge, clean the contacts from grease and dirt.

Replacing the lighting lamp in Samsung and Atlant refrigerators

The lampshades of these refrigeration units are held on by screws. The lighting device is mounted on contacts or connectors.

So, to change a light bulb, you need:

• disconnect the refrigerator from the power supply by turning it off;
• Unscrew the screws on the lampshade and remove the lampshade;
• disconnect connectors and contacts;
• Unscrew the burnt out lamp and screw in a new one;
• secure the lamp with screws.

Some Samsung have a protective strip that is removed before replacing the lamp in the refrigerator.

How to extend the life of a light bulb

To avoid having to change the lamp frequently, you need to follow a few simple rules:

• Keep an eye on the humidity in your refrigerator, as condensation and water cause frequent lamp replacement.
• For refrigeration appliances, install a Euro socket with a grounding function.
• Use the refrigerator only in accordance with the instructions. Pay particular attention to humidity and temperature conditions.
• Voltage surges are also one of the reasons why light bulbs burn out. Use a surge protector or uninterruptible power supply.
• Although the type of lighting is not an indicator of the quality of the refrigerator, when purchasing, give preference to installations with LED lamps. They are reliable and durable.

If the light bulb burns out without working for the required time, check the shutdown button, which is usually located inside the camera on the side or top panel. Deformation of the door can lead to the fact that the lighting device works around the clock, the light is on even when the door is closed. Fixing the problem is simple: stick a polystyrene plate of the required width onto the button itself.

In this article, we tried to describe in detail the process of replacing a light bulb in a refrigerator Atlant, Indesit, Samsung, etc. We hope our article helped you!

If you open the refrigerator and find complete darkness, then you should not immediately unscrew the lamp - first you need to determine the cause of the problem.

How to change a light bulb in a Stinol refrigerator?

Appliances from domestic and foreign manufacturers are equipped with a light that turns on when the door is opened. However, sometimes the light bulb burns out, and in order not to spend money on the services of a technician, we will give recommendations on how to change the light bulb in domestic refrigerators Stinol, Atlant, Biryusa.

What lighting systems are used

Old refrigerator lamps are no different from regular lamps - they have an incandescent filament that glows with electricity and emits light. The metal of such a thread burns out after some time, after which the lighting needs to be replaced . New units use modernized lighting, which cannot always be replaced on your own.

Standard lighting system using Atlant technology

Today, manufacturers equip refrigerators with one of the types of lighting:

• incandescent lamp at the top of the refrigerator compartment. The specifics of the operation assume that when the door is closed, the button is pressed and the light goes out because the electrical circuit is broken.

Incandescent lamp at the top of the refrigerator compartment

• Similarly, when the door is opened, the lighting turns on. The service life is expected to be about 1000 hours;
• halogen lamps. Provide brighter light while consuming minimal energy;
• luminescent with cold light. They last 8000-11000 hours;
• LEDs are used in modern models. They are the most economical and safe, service life up to 11 years. Replacement is carried out only by a master.

Why does the lamp stop burning?

If, when you open the door, you notice that the light in your refrigerator is not on or is blinking, you must first determine why the problem occurred. Flashing may be caused by voltage fluctuations and surges in the electrical network. If the lights do not turn on, follow these steps to identify the cause:

• check the presence of electricity by clicking the switch - most likely, the electricity in the apartment is turned off;
• inspect the cord for damage to the insulation;
• check the functionality of the outlet by connecting another working device;
• if the appliance does not turn on and does not cool the food, a serious breakdown may have occurred;
• the light bulb has burned out - in this case it needs to be replaced;
• The cartridge or its contacts may be damaged, which will require calling a technician.

If, as a result of such diagnostics, you have discovered that a light bulb has burned out, replacing it on a domestic refrigerator is not difficult.

What are the lights in the refrigerator for?

As we have already said, light bulbs in refrigeration equipment are needed in order to see all the products located inside. However, manufacturers have provided other functions for lighting:

• properly selected lighting will allow you to promptly identify spoiled products, so it is recommended to install models with cold light, because warm light “embellishes” the food.
• The lamp allows you to determine how tightly the refrigerator door is closed, because everyone knows that when the unit closes tightly, the lighting device goes out.

Why do the light bulbs in the refrigerator burn out?

Before changing the lighting fixtures in the refrigerator, find the cause of the problem. Diagnostics is carried out in compliance with the following steps:

• check the operation of the switch;
• inspect the electrical wiring of household appliances;
• check the serviceability of the socket;
• monitor the operation of the refrigerator (presence of noise, delays in turning on and off).

Burnout of light bulbs in a refrigeration unit occurs for the following reasons:

• damage to the power cable insulation;
• burnt out socket;
• breakdown of the motor, compressor;
• malfunctions of the unit (damage to the cartridge, buttons);
• power outages;
• increased load on equipment;
• operation in case of non-compliance with safety rules, etc.

If there are no breakdowns, the lighting device will need to be replaced.

What types of light bulbs are there?

In all devices produced in the USSR, only one type of lamp was used - vacuum. They were similar to those installed in ceiling chandeliers, but with less power. Of course, even now you can find models with such lamps on the market. However, manufacturers prefer to use other methods of lighting modern refrigerators.

Table No. 1. Types of light bulbs for refrigerators.

Prices for different types of light bulbs for the Indesit refrigerator

What light bulbs are used and how to choose

Before replacing a lighting fixture, it is necessary to determine which bulb is used for the existing brand of household appliances and measure the diameter of the base.

The list of popular light bulbs for refrigeration units:

1. Incandescent lamps. Budget, but not economical. The devices are common in inexpensive refrigerator models. They produce a yellowish light and may become overheated during prolonged use. The service life of incandescent lamps is about 1 thousand hours. Disadvantage: sensitivity to voltage changes.
2. Halogen. They are distinguished by intense bright light, do not overheat, and have an unusual shape. The energy efficiency of halogen lighting devices is higher than that of incandescent lamps. Performance lasts up to 4000 hours.
3. LED. They are environmentally friendly, highly energy efficient, and hardly heat up. The operating period is 100 thousand hours.
4. Luminescent. They are distinguished by their ability to reproduce daylight and ensure comfortable operation of refrigeration equipment. The service life of the light bulbs is no more than 15 thousand hours. The disadvantage is the presence of mercury vapor in the devices.

View » Why in the Atlant two-chamber refrigerator the refrigerator compartment does not work but the freezer works: reasons for the breakdown, what is the problem, what to do

The power of the light bulb depends on the location of the element in the refrigerator and ranges from 11-40 W. Standard models use 15-25 W lamps. Large equipment is equipped with 2-3 lamps or 1 lamp with increased power. When selecting a lamp, the load on the electrical network in the room is taken into account. The characteristics depend on the number of devices being used and their dimensions (a two-chamber unit consumes more electricity).

Indesit

The Indesit brand refrigerator uses fluorescent light bulbs with an E14 base type. The power is determined by the type of equipment (number of cameras, dimensions, model). The standard power of light bulbs for household appliances is up to 40 W. In large-sized equipment (with 2-3 cameras), several medium-power lamps are installed.

Atlant and Biryusa

Atlant brand refrigerators use light bulbs with E14 socket. Biryusa units are equipped with LED devices. However, manufacturers can change the contents of refrigerators. Therefore, when replacing a light bulb, the appropriate type of base, operating technology, and light intensity are selected.

Samsung and Hotpoint Ariston

Samsung refrigeration equipment uses bulbs with an E12 base type, while Ariston Hotpoint uses E14. The types of lighting devices (LED, halogen) are determined by the model (modern, outdated), the volume of the refrigeration unit, etc.

What is the power and where are the lamps located?

It is worth considering that the final cost of the device does not depend on the light bulb. So, in small and medium-sized refrigerators there is only one lamp with a power of no more than 25 W. If you have a large-sized device, this will not be enough, so install either two lamps with a power of about 20 W, or one with a power of about 45 W.

The lighting is usually placed on the side panel on the side where the door is attached - then the lamp is connected to the switch. However, there are other lamp placement methods that you should familiarize yourself with before proceeding with replacement:

• on the side closer to the back wall;
• on the back wall;
• above;
• on the ledge.

The best placement option is the back wall or the side wall next to it - this allows you to get uniform lighting on each side. If the light bulb is on top, then only the upper shelves are clearly visible, which makes using the lower ones inconvenient. This nuance is especially important in the presence of a large-sized device. The worst placement option is considered to be a visor - then there will be little light in all parts of the refrigerator.

Power and location

The selling price does not depend on what kind of lamp is installed in the refrigerator. In small units, one lamp is installed with the following power:

• 15 W;
• 25 W.

For a large refrigerator, such lighting is not enough, so the solution is this:

• install 2 lamps 15-25 W;
• install one 40 W lamp.

Important! What should you do if there is not a pleasant aroma of food in the refrigerator, but a musty smell that does not induce a sense of appetite at all? We know about this problem and to help you, we have put together a number of effective methods to combat stench, which you can find out by clicking on the direct link “How to remove odor from a No Frost refrigerator?”

The lamp is usually placed on the side wall closer to the door. In this case, it is combined with the switch. There are other possible methods that you need to know about in order to determine where to change the light bulb in the refrigerator:

• on the side wall closer to the rear panel;
• on the back panel;
• on the top panel;
• on the visor.

Important! The best location is on the back panel or next to it on the side. The lighting is uniform. If the lamp hangs on the “ceiling”, the upper shelves are brightly illuminated, while the lower ones are in twilight. This is especially important if the unit is large. The worst location is on the visor. In this case, all parts of the camera are lit very poorly.

Top panel

The light source installed on the top panel illuminates only the products located on the upper shelves, leaving twilight below.

Why the lamp does not light: reasons

If you open the refrigerator and find complete darkness, then you should not immediately unscrew the lamp - first you need to determine the cause of the problem.

You will need to do the following:

1. If the device operates silently, then it is necessary to check the integrity of the wiring.
2. You should check the serviceability of the outlet by connecting another device to it.

1. It is necessary to check the functionality of the refrigeration equipment. If about half an hour has passed, and the unit is still operating quietly, then the problem is in its internal structure, and not in the light bulb (perhaps the compressor or motor has become unusable).

How to choose a lamp?

Experts recommend purchasing any parts and lamps from the same brand as the refrigerator itself. You can find an identical model in specialized centers where they repair similar units. Of course, such a light bulb will cost more than a standard model from a store, but it will fit perfectly into the refrigerator.

If there is no specialized center in your city, then you should try to find a similar lamp in a specialized store. To do this, you will first need to dismantle the old one and bring it to the store.

When choosing a light bulb, take into account the following criteria:

Most often, store consultants can tell you which model a particular light bulb fits. However, it is necessary to independently compare your option with those available on the display case.

When choosing power, you should also be careful, because even if the light bulbs have the same number of watts, the degree of illumination can differ significantly. For example, LED models shine much brighter than standard vacuum ones.

What kind of light bulbs are used?

Depending on the design and parameters of the refrigerator, the following types are installed inside the chamber:

• incandescent lamps;
• LED;
• luminescent;
• halogen.

If you are wondering which light bulb is best for installation instead of a product that has burned out, you need to study the basic parameters of each option. For example, an incandescent lamp is the simplest in operating principle and does not last long (the average is 1000 hours). It produces yellow radiation, which is considered the most comfortable for the eyes. This option has a significant drawback: it is distinguished by high power. According to this criterion, it is inferior to more modern analogues.

Considering that the dimensions of the refrigerator chamber are relatively small, the level of energy consumption when turning on an incandescent lamp increases slightly. For this reason, such light sources are still used in single- and double-chamber units.

An LED refrigerator light is the best choice. It does not heat up, which means it will not affect the microclimate of the unit during operation. In addition, this type of lamp is resistant to temperature changes and low values ​​of this parameter. There are a large number of models of such products. In addition, they differ in color temperature, which allows you to select a light bulb that produces radiation of the required shade (white, neutral, yellow, etc.).

The price of this option today is acceptable. The idea that such light bulbs are expensive is a myth. Considering that they last much longer than their incandescent counterparts (30-50 times), it is advisable to purchase a product based on LEDs. It is distinguished by a long service life. However, you need to remember that over time (closer to the end of their service life) such light bulbs begin to dim. This phenomenon is the result of their working mechanism. Loss of light saturation occurs after decades of intermittent use (as in the case of a refrigerator).

Fluorescent lamps are similar in properties to their LED counterparts, but last less - up to 15,000 hours, and they also operate on a different principle (they contain a gaseous substance inside). However, this is a fairly long period, considering that the lamp in the refrigerator is not constantly on. It is also noted that this variety produces cold light.

In large-sized appliances, halogen light bulbs are also found. They are in many ways similar to incandescent counterparts, but last longer - up to 2000 hours. The disadvantage of the halogen version is the high heating intensity. It is also distinguished by significant power. These factors may contribute to a slight increase in energy consumption. They explode when touched. This phenomenon is due to a significant increase in the heating temperature of the glass flask at 1 point on the surface of the product.

When choosing a lamp, the load on the electrical network is also taken into account. To illuminate the chamber inside the refrigerator, there is no need to install powerful products: 60, 100 or more W. This is an unnecessary waste of energy. The power limit for refrigerator lamps is 40 W. However, this option is suitable for lighting large devices.

If LED lamps are installed, in this case the power varies between 15-25 W. This is enough to illuminate a medium-sized camera. If the refrigerator is large, install 2 lamps of moderate power or 1 piece, but of higher power.

Replacing a light bulb

After purchasing a lamp, you will need to insert it into the lampshade. Here, novice craftsmen may encounter difficulties, because screwing in a lamp is not difficult, but they still have to get to it. So, for some models the lampshade is first dismantled, for others this should not be done.

Replacing a light bulb in an Indesit refrigerator: step-by-step instructions

Step 1. First, you need to disconnect the refrigerator from the power supply. In addition, you will need to remove all products and shelves from it (if they interfere with the repair)

Step 2. Next, you should unscrew the screw fastening using a screwdriver, which will allow you to bend part of the lampshade.

Step 3. Now you should remove the old lamp if it is in the socket.

Step 4. Now you need to screw in the new lamp, moving in the reverse order.

Step 5. Now you need to return the bent part of the lampshade to its usual position.

Once you have completed replacing the light bulb, you will need to check its functionality. To do this, you need to plug in the refrigerator.

Note! The lighting in the Ariston unit is replaced using the same principle - this means that the lampshade does not have to be removed.

Video - Replacing a light bulb in an Indesit refrigerator

How to replace the light button in the Indesit refrigerator?

It is advisable to repair the lighting button in units of this brand if there is a specialized store with spare parts nearby. Usually the spring inside the button wears out, which allows you to turn the light on and off.

In order to carry out repairs, you will first need to dismantle the button and then open its body into two parts using a sharp knife. Now you can install a new spring in place of the old one. In other cases, it is better to immediately purchase a new lighting key and install it. In addition, you do not have to spend a lot of time on this process.

Note! If a light bulb regularly burns out earlier than expected, then you should pay attention to the light button. If it breaks down, a short circuit can occur at any time, causing not only the lamp to burn out, but also the lampshade itself.

Video - Replacing the light button on the refrigerator

Features of replacing a light bulb in refrigerators from another manufacturer

Table No. 2. Replacing light bulbs in other units.

Replacing a light bulb in an Indesit, Atlant, Samsung refrigerator

Replacing the lighting in the refrigerator depends on its type. In old-type refrigerators, conventional incandescent lamps were most often installed, which were located on the ceiling of the unit. The operating principle of the lighting in this case is quite simple: there is a switch next to the refrigerator door, which becomes jammed when the door is closed. The moment the refrigerator is closed, the circuit is open. Accordingly, the light does not come on. Despite the fact that the incandescent lamp is quite inexpensive, it has to be changed frequently, since its service life does not exceed 1000 hours.

The same operating principle works with a halogen lamp. It is worth noting that both types of lamps have a clear drawback: when burned, they emit heat, which negatively affects the operation of the cooling device. The only difference between a halogen lamp and an incandescent lamp is that the former has a much higher light output.

In more modern models, you can increasingly see fluorescent lighting fixtures. They can be distinguished from the previous ones by the cold diffused light. Unlike previous types, this one does not heat up during operation. And its service life varies from 8 to 11 thousand hours.

Useful tips

To avoid having to constantly change the light bulbs in your refrigerator, you must follow these tips:

• You should promptly wipe away all drops of water inside, because condensation does not have the best effect on the performance of lighting fixtures;
• the presence of grounding will prevent damage to electrical appliances and light bulbs. In addition, it is advisable to install an uninterruptible power supply;

• An LED lamp is considered durable, but at the same time it has a high cost. However, experts recommend not saving, because vacuum models will have to be purchased constantly. It should be borne in mind that such lighting cannot be installed on every refrigerator, so it is advisable to ask the store sales staff about this in advance;
• Some refrigerators, according to the operating instructions, require regular defrosting, so this procedure should not be avoided;

• Each unit comes with detailed instructions regarding its operation and temperature conditions. Following these recommendations will not only prolong the life of the light bulb, but also the entire refrigerator.

Prices for various types of uninterruptible power supplies

Lifehacks

• When replacing halogen products, avoid touching their surface with bare hands: the biological traces left subsequently lead to spot overheating and rapid failure - use fabric or rubber gloves. Screw in slowly so that the lamp fits neatly into the thread of the socket.
• Luminescent consumables are very fragile, so when installing them, you need to hold on to the base so as not to break them.
• Often, the accompanying documentation for household appliances contains detailed information on how to troubleshoot basic minor problems, including how to replace a light bulb if it does not light.

Save on lamps

Lamps for refrigerators, of course, are inexpensive, however, you don’t want to change them every week either. To avoid having to do this, it is useful to follow a few simple rules:

1. When buying a refrigerator, all other things being equal, give preference to the one in which you can use LEDs - this will protect both your products and your unit from a lot of troubles.
2. High humidity can cause lamps to burn out quickly, so do not forget to monitor this parameter.
3. Use only outlets that have a grounding bus.
4. Each unit has instructions that say what conditions it is intended for - use the refrigerator only in such conditions, then both it and the light bulb will last longer.
5. Voltage surges can cause many unpleasant moments: a surge protector or an uninterruptible power supply will help you out.

Important! Due to the fact that fresh greens are a highly perishable product, it is very important to take care of the correct storage conditions, such as special containers. With their help, lettuce, arugula or spinach leaves will remain fresh and not fade so quickly. To enjoy fresh and healthy salads every day, check out another article on how to choose the right containers for storing greens.

How to extend lifespan

Here are some tips for extending the life of your refrigerator lights:

• When purchasing, opt for units with LED lighting. They last longer and are more environmentally friendly than their counterparts.
• Control the level of humidity inside, promptly remove condensation from the walls and shelves of the device, and prevent moisture from getting on the indicators and lighting elements.
• A grounded outlet, plus an uninterruptible power supply, allows you to avoid damage to household appliances.
• Defrost the main compartment and freezer promptly and regularly.

What to do if the base remains in the socket

There are situations when, when trying to unscrew an incandescent lamp from the lampshade, it breaks and the base remains inside the socket. In this case, you need to proceed as follows:

• Be sure to turn off the power from the outlet, otherwise you will get an electric shock.
• Carefully remove any debris from the refrigerator shelf.
• Spread a towel or bag under the cartridge to make it easier to collect the remaining glass.
• Prepare thick fabric gloves for work.
• We take pliers and unscrew the remaining base carefully, without applying too much force, to avoid deformation.

Sources

• https://womanadvice.ru/lampochka-dlya-holodilnika
• https://hozzi.ru/sovety/kak-pomenyat-lampochku-v-holodilnike-atlant
• https://expertland.ru/tehnika/holodilniki/kak-pomenyat-lampochku
• https://sdelai-lestnicu.ru/obustrojstvo/kak-pomenat-lampocku-v-holodilnike-atlant-posagovaa-instrukcia-osibki
• https://serviceyard.net/tehnika/kak-pomenyat-lampochku-v-holodilnike-indezit.html
• https://100ab.ru/steny/kak-pomenyat-lampochku-v-holodilnike-indezit.html
• https://Tehno.expert/holodilnik/kak-pomenyat-lampochku-v-atlant.html

In what cases is it better to use the services of a specialist?

Of course, replacing the lamp in the refrigerator yourself will save your budget on the services of a specialist. However, sometimes you cannot do without the help of a professional.

The advantages of professional replacement should be highlighted:

1. Technicians have equipment in their arsenal to diagnose equipment in order to identify the cause of a malfunction. After all, sometimes, in addition to the light bulb, other functional elements of the device fail.
2. Our specialists provide a guarantee for their work, so if any complaints arise, you can contact the company again, but for free.
3. Professionals do the job much faster, while a beginner will need several hours just to figure out the problem.

In addition, many craftsmen have in stock an assortment of light bulbs suitable for different models of refrigerators, so you don’t have to look for a similar option in stores yourself.

Find out how to transport a refrigerator lying down or standing up, and also read the recommendations in a special article on our portal.