Why doesn’t the LG automatic washing machine spin out clothes, what should I do?

The problem with no spin may appear suddenly. Sometimes the situation with the water remaining after washing in LG is due to the impossibility of spinning the laundry, but it is also possible that there is simply no drainage.

To understand what exactly the problem is, you should analyze the operation of the nodes involved in the process.

Why the LG washing machine does not spin clothes and how to fix the problem, we will tell you further.

Wash without spin

The first reason may be that the consumer has not read the operating instructions, but is content with the information that is presented on the control panel.

Some programs do not require the LV machine to wring out the laundry. If the washing modes are set for silk or other delicate fabrics, the unit completes the process without spinning. It is launched manually by pressing the desired button on the panel.

In some cases, it turns out that when selecting a program on the washing machine, the spin off button was pressed, so the LG machine stops working after draining the water.

Why doesn't the spin cycle work?

There are many reasons why a washing machine ceases to cope with its direct responsibilities. Let's look at the main reasons why a washing machine stops spinning clothes:

• Spin is programmatically disabled in the settings or gentle washing is used;
• the drain pump system is faulty;
• the motor brushes are worn out;
• electronic module is faulty;
• the water level sensor is broken;
• the operation of the heating element is disrupted;
• the machine is overloaded with a large amount of laundry;
• the tachogenerator has failed;
• There was a serious breakdown in the engine.

Imbalance of loaded laundry in the drum

The reason that the laundry remains wet after washing is a violation of the loading rules. If the drum is overloaded, a safety mechanism is activated. The process is stopped to prevent equipment failure.

In this case, you need to take out the excess items and squeeze them out in the machine in parts, starting the desired mode separately.

If the item is light but takes up the entire space of the drum (for example, a bulky jacket), the washing machine will not spin it either.

Low filling of the drum can also lead to problems.

Small things can clump together, causing imbalance. Therefore, it is recommended to wash them together with large ones.

To ensure that the clothes are evenly distributed inside, special balls are used that prevent imbalance in the device during spinning.

If the washing machine is stuck on the spin cycle, what should you do?

First of all, check your wash settings. In some modes, spinning is either not provided at all or is turned on manually after a long soaking (rinsing). Start the cycle manually and wait until the wash finishes.

One of the frequent failures during the operation of washing machines is the situation when the washing machine freezes at one time each time, and this time period corresponds to the beginning of the spin cycle. This may be caused by:

• insufficient or excessive loading of the drum with laundry;
• loading one too heavy or bulky item;
• jamming of the drum with a foreign object.

If the washing machine stops during washing for these reasons, it will not be difficult for an experienced owner to fix them without calling a service center specialist.

Drain pump malfunction

Along with the engine, the drain pump experiences a heavy load, which leads to its wear. In addition, it becomes clogged because waste water passes through it, particles of which settle on the walls of the equipment and hose.

To determine whether the pump is the reason why the washing machine is not spinning clothes, you need to listen to how the pump operates. If it makes a louder noise than before problems with draining occurred, or, conversely, you cannot hear the sounds of a running motor, the problem is in this part of the device.

Before deciding to replace a component, you need to make sure that the other components of the pump are in order:

1. Filter and drain hose. They need to be cleaned before a problem occurs. The filter is at the bottom left. Before unscrewing the plug and removing the hose, you need to place a rag so that the remaining water in it does not spill out onto the floor.
2. Impeller. It is located behind the filter. It is checked for the presence of foreign objects - lint, hair, solids that may interfere with the free rotation of the blades.

If these elements are in order, this means that the pump or its parts must be replaced. Without the skills to carry out such repairs, it is better to call a specialist who will determine why the LG machine has stopped spinning.

To solve the problem yourself, you need to know the structure of the unit. To remove the pump, place the machine on its side and remove the bottom cover. An inspection will show what needs to be replaced - the pump or individual components:

• impeller;
• rubber gaskets;
• pulley;
• contacts;
• sensor;
• cuff;
• axis.

In order for spare parts to fit the car model, they are selected according to the serial numbers indicated on them.

Clogged drain hose or drain

The drain hose may stop draining waste water due to contamination. In such a situation, this means that the reason is not that the LG washing machine does not spin the clothes, but that the liquid remains inside.

If natural waste accumulates in the drain pipe (clothing fibers, animal hair, scale), using a chemical to clean the system may be sufficient.

If mechanical contamination, a clothing button, a coin, etc. gets there, you will have to disassemble the drain. To do this you need:

1. Disconnect the unit from the mains and drain the water.
2. Remove the hose from the sewer network.
3. Turn the car over on its side, placing a rag under it.
4. Remove the bottom panel and filter.
5. Release the clamp that holds the hose.
6. Disconnect the latter from the pump and from the housing.
7. Clean the tube using a cable or brush.
8. Connect all elements of the system and run a test wash.

If during the inspection it turns out that the sewer is clogged, it is necessary to clear the pipes of the blockage mechanically using a cable or a chemical agent.

To prevent breakdowns, it is recommended to do the following:

• check your clothing pockets to ensure that there are no objects left in them that could cause mechanical contamination of the drain;
• use detergents recommended by the manufacturer;
• clean the machine from scale and other types of blockages using special means;
• install an additional filter on the drain pipe;
• add water softening agents when washing.

LG machine does not spin: what you can do yourself

Sometimes the problem may be due to operating errors, incorrect installation or the selected program. Here is a list of reasons for the lack of spinning that you can deal with on your own.

• The “No spin” program is selected. In programs for delicate fabrics, there is no spin or the machine spins at low speeds. Also, in some LG models you can disable the spin using an additional function. Check which program you have selected and whether you have accidentally activated the No Spin function.
• The LG machine is not installed level. If it “mews” on one side, then the washing machine will not be able to evenly arrange the clothes for spinning. To fix the problem, set the machine level.
• LG machine is overloaded with laundry. Check whether the weight of the loaded items corresponds to the selected program. The maximum weight for each program is indicated in the instructions for your washing machine. You may have overloaded the machine, so it can't wring things out.
• A heavy object is being washed. Modern LG washing machines are equipped with a drum balance control system. If you wash one heavy item, for example, a rug or bathrobe, the machine will not be able to distribute it evenly across the drum and will not spin it out. Add a towel, sweatshirt or any other medium-weight item to the drum and start the spin cycle again.
• The load of laundry is not evenly distributed. It may have clumped into a lump, so the LG machine cannot distribute things evenly throughout the drum and does not wring out. Open the washer and lay out the laundry manually, then restart the spin cycle.
• Too few items loaded. A low machine load can also cause imbalance. Add one or two items of similar weight to those being washed to evenly distribute the laundry throughout the drum.
• One-time electronic failure. Due to power surges, the control board may fail. Try unplugging your LG washing machine for 10-15 minutes, then spin again.

Breakdown of the pressure switch

A malfunction of the water level sensor, or pressure switch, manifests itself in the fact that the laundry does not spin out and the LG washing machine produces wet clothes after washing.

The pressure switch is located on the side wall under the top cover on the back of the device. The dismantled sensor is inspected for external damage and tested for performance using a multimeter. Another method is to blow out the sensor, for which a hose is put on the fitting. If a click is heard when air is supplied, this means that the device is working properly.

If it is damaged, it is replaced completely, because... The pressure switch cannot be disassembled into components.

Possible causes of failure

1. the motor has failed.
2. The tachometer is faulty.
3. The control module is faulty.

With prolonged use of the device, the motor, which is responsible for the movement of the tank, becomes unusable. The engine in LG automatic washing machines is very reliable. Breakage can only occur 10 years after the start of use. After the ten-year period has expired, the machine may not only fail to wring things out, but generally malfunction. Problems can be solved simply - you need to replace the motor. With constant overload, do not be surprised that the LG machine stops spinning. This occurs as a result of a malfunction of the tachometer.

In this case, the help of a specialist will help you. Call a specialist to your home and he will fix the breakdown and replace the failed part. The main board that coordinates the operation of the washing unit is the control module. Malfunctions in its operation directly affect the quality of the spin cycle. And also for rinsing and water intake. The problem is solved by a technician who will replace the board. If you notice that your machine has stopped draining water and is not spinning clothes well, try to determine the cause of the problem. The drain pipe is probably clogged.

It needs to be cleaned. Then evaluate the drum load. If there is excess laundry, open the car door and take out the excess. Overloading of laundry directly affects the quality of washing, rinsing, and spinning. If all the above steps do not give positive results, then you need to unplug the washing machine, wait a while and turn it on again. Reboot. Programs often crash, which can be resolved by rebooting. If this time the problem is not solved, then call a specialist. When the washing machine drum is frequently overloaded, the sensor responsible for the speed breaks. If it breaks, the washing machine stops spinning. This happens very rarely, but it does happen.

It is likely that the problem is not even in the sensor, but in the wires that extend from the sensor and periodically oxidize. Their fastening may be loose. It is very rare that a washing machine does not work due to a burnt out motor. LG machines are equipped with inverter motors, they are very reliable and last at least 10 years. Changing an engine is a very expensive proposition. You can replace the tachometer yourself. There are problems with the control module. The functionality of the control module can be easily checked by running the diagnostic mode. The diagnostic mode is available in all modern LG washing machines.

Plug in the machine and wait for the sound signal. Then press 2 buttons “spin” and “temp” at once. Start diagnostic mode. Then click the "Start" button. Your door should be locked. Press the “Start” button again, your washing machine will go into spin mode. If in this case it does not make revolutions, then there is a breakdown.

You need to do the following:

1. Remove the rear panel of the case. Open access to the washing machine motor.
2. Pick up a tester or multimeter and measure the AC voltage.
3. Remove the chip with wires.

Next you need to measure the voltage between the wire contacts. If it is within 140 - 150 volts, then everything is fine. If there is no voltage, the module will have to be replaced. What to do if the pressure switch fails? There is a pressure switch sensor in the washing machine tank. It determines the water level in the tank and transmits information to the electronic chip of the machine. The washing machine may not understand how much water is in the tank, as a result of which it stops pumping it out. The pressure switch cannot be repaired; it is better to replace it with a new one. A car is quite an expensive thing. The right decision would be if people from the LG service center take care of its repair.

Control system failure

System malfunctions occur due to voltage fluctuations in the electrical network or due to wear and tear of control panel components. Wires and contacts may oxidize or burn out, plastic parts may become unusable, etc.

In some cases, this failure can be resolved by rebooting the system. In other cases, it is necessary to carry out diagnostics using special equipment. To do this, it is better to call a technician or contact a service center.

The latest versions of LG have a self-diagnosis function programmed. To carry out this procedure, download a special application to your smartphone. There is another option - contact the service center by telephone and follow the operator’s instructions to transmit information about the diagnostic results.

Pump removal and repair

To detect a blockage, you first need to open the base panel from the bottom on the front part and unscrew the drain filter. It is necessary to substitute some kind of container, because in the process the remaining water will spill out. After removal, the part must be thoroughly cleaned of debris and dirt that has accumulated during operation of the LG washing machine. Also, during washing, coins, paper clips, bones from women's underwear, buttons and other small items get here. Most often, they are the cause of the blockage.

The next thing to do is to inspect the drain hose, make sure that it is not pinched, then disconnect it, blow it out, or, if a large accumulation of dirt is detected, clean it with a plumbing cable. Then return the hose to its original place and install it correctly.

Next, you need to inspect the place where the drain hose connects to the sewer. You should make sure that there is no blockage at this point, and if necessary, clean the siphon and pipes.

Now you need to inspect the internal components of the LG washing machine.

It is necessary to disconnect the equipment from the network, water supply and sewerage and move it to a spacious place. Further actions are as follows:

• Remove the detergent drawer.
• Turn the LG washing machine on its left side.
• Unclench the clamps and remove the drain pipe coming from the water tank.
• Remove the part, check for debris, clean and rinse.
• Disconnect the pump by unscrewing the retaining fasteners.

The pump must be disassembled into two parts and the impeller inspected. It often has hair, threads, and pieces of fabric wrapped around it. This makes it difficult for the part to rotate and leads to pump failure. If the impeller is clean and there are no foreign elements on it, you need to check the pump with a multimeter.

The measuring device must be switched to resistance testing mode and the probes must be installed on the pump contacts. If the numbers “0” or “1” appear on the display, the part should be replaced. A new drain pump must be purchased strictly in accordance with the device model; this can be done at a service center or in a specialized store. Another option is to order a sump pump online. A new part must be installed in place of the damaged one, then assemble the LG washing machine, connect it to the network and communications, and check the equipment by running a test wash.

Why did the washing machine stop rinsing and what should I do?

If the washing machine stops rinsing, then the reason is not always some kind of large-scale breakdown. Behind this unpleasant symptom there are often user errors or trivial troubles that can be easily dealt with without contacting service center specialists.

We will talk about why the car freezes and what to do in this case in this review.

Stuck during washing

If the simplest reasons for stopping work have been verified, then it is necessary to move on to a serious analysis of the performance of the nodes. In order to narrow the scope of work, it is necessary to determine at what stage of the wash the freeze occurred.

Doesn't take up water

If the washing machine cannot fill with water, the program stops and the wash does not even start. In this case, the freeze appears right at the beginning of a given work cycle. To determine the exact reason for the LG stopping, you need to check all the systems that are involved in collecting water one by one .

The heating element burned out

A malfunction of the heating element in LG leads to a stop in operation.

In this case, the electronic unit sends a signal about the need to heat the water, but the heating element cannot carry out this work. As a result, the machine fills with water and the cycle stops.

You can make sure that the reason is in the heating element by carefully testing the temperature of the sunroof glass. If it is cold, then the problem is in the heating element . This hang-up can be solved by replacing the heating element. This article will tell you how to replace the heating element.

Damage to the water level sensor

The pressure switch is another important component, if it fails, washing may not even start. This part is responsible for determining the water level. If the pressure switch breaks, it is replaced with a new one.

Motor brush wear

In LG commutator-type machines, the motor brushes are responsible for transmitting rotational motion to the drum. If there is significant wear, contact is lost and the drum cannot accelerate to the desired spin speed. Over time, the problem even extends to washing - the drum does not rotate at all. The issue is resolved by replacing the brushes with new ones . Read how to do this here.

Drum jamming

If a foreign object gets between the tank and the drum, the rotation may stop. If the drum is jammed, the LG washing machine freezes.

Jamming can be caused either by the ingress of small objects (coin, key, etc.) or by distortion of the drum due to failed bearings. Since the drum cannot turn, the laundry processing process stops.

Diagnostics is necessary to accurately determine the cause of the rotation stop. If it turns out that the problem is a foreign object, it will need to be removed. If there is a problem with the bearings, they are replaced along with the seal . Read how to change bearings here.

Drain violation

During washing, the LG machine fills and drains water several times per cycle. If water cannot be removed, the program execution process stops.

If such a malfunction occurs during washing, soapy water remains in the drum. It is impossible to immediately give a conclusion as to the reason for the lack of drainage in LG - diagnostics and checking of all components is necessary .

This can be either an easily removable blockage or serious damage, for example, to a pump or control unit.

Control module malfunction

If the LG control module breaks down, freezing can occur at almost any stage of processing items, including the washing stage. To analyze the performance of the circuit, it is necessary to partially disassemble the washing machine itself, disconnect the board, and test and repair it in a workshop.

The engine has become unusable

An LG engine can become unusable for various reasons - from voltage surges to water getting on it, long-term use and physical wear. If this particular part is to blame for the freezing, in most cases it has to be replaced with a new one rather than repaired . You can find out how to do this here.

Indirect reasons for stopping the washing machine

After washing and rinsing, did the washing machine freeze or spin the drum several times and stop? Start by eliminating reasons related to the way the machine is controlled. Namely:

• Check the set mode. Perhaps a program without draining and spinning has been selected? This is likely when washing woolen and delicate fabrics. Then just turn on the spin cycle to get things working.
• Make sure the drum is not overloaded with laundry. When things get wet, they become heavier, and rapid rotations can damage the drive mechanism. Therefore, the machine stops working. It is enough to open the hatch and take out some of the things.
• Are you sure it's not an imbalance? This happens when one large thing is downloaded. The drum spins, which knocks the laundry into a heavy lump and leads to imbalance. To fix the problem, distribute the items evenly in the drum.

Such errors in handling equipment lead to the stoppage of all automatic washing machines that are equipped with electronic controls. These can be models from Samsung, LG, Indesit and other brands.

Possible problems

Repairing a washing machine should begin by inspecting the drum. There is probably a foreign object inside: a coin, a bra wire, a sock, a button, etc. Foreign elements can cause the washing machine to stop working. The reason for the equipment freezing during the spin cycle can also be:

• severe wear of shock absorbers. Modern washing technology is very sensitive to errors in the operation of the system. During spinning, there is increased vibration of the device, which is absorbed by dampers and springs. Wear of the shock-absorbing elements can cause the drum to freeze and stop the operation of the equipment. The repair will consist of replacing shock absorbers;
• malfunction of the electric motor and tachometer. The motor electronics are probably damaged or the brushes are deformed. The Hall sensor records the number of engine revolutions; if it fails, a new, serviceable tachometer should be installed;
• Damage to the water level sensor. The pressure switch transmits signals about the volume of water in the tank to the control module. If the sensor does not function, the operation of the automatic machine stops between the “Rinse” and “Spin” options;
• impossibility of draining waste liquid from the tank. The washing machine must empty the tank of water before the spin process. If the drum is filled with water, the machine will not be able to begin spinning the laundry. In this case, you need to examine the drainage system of the equipment, as well as the sewer pipe for blockages;
• damage to the main control unit. This can happen due to a voltage drop in the electrical network. Also, a module malfunction occurs when the part is exposed to moisture.

If you have insufficient experience working with washing machine electronics, it is better to entrust repair of the control board to a qualified technician.

What to do if damage is detected? The further nature of the work directly depends on the detected malfunction. Let's look at the main areas of activity in car repair.