The washing machine does not spin or drain water - what should I do?

Beko washing machine does not spin

If the cycle has ended, and there is water or completely wet clothes left in the drum, then there is only one conclusion - the washing machine does not spin. This kind of trouble often occurs with washing machines from VEKO, and it is not always a large-scale problem. Our article will help you understand what led to the failure, simple inattention or a serious problem. We will analyze possible sources of defective spinning and provide instructions for eliminating them.

List of possible problems

You shouldn't tolerate wet laundry. Finishing a thankless job with the washing machine is not only unpleasant and time-consuming, but what’s worse is that an unresolved breakdown can aggravate the problem to the point of a disastrous outcome. To know where to look for a problem, you need to understand the range of possible causes of a failed spin cycle. For Beko models we are talking about the following situations:

• No spin program selected;
• there is an imbalance in the drum;
• the drain does not function;
• the tachogenerator has failed;
• the electric motor broke down;
• drum bearings are worn out;
• the control board does not work;
• a foreign body has entered the tank, preventing the drum from spinning.

In 99% of cases, the problem that has arisen can be solved independently. The help of a professional repairman is only needed if the control module is burned out. All that remains is to correctly diagnose the source of the problem, for which it is enough to consistently check each possible option. Step-by-step instructions are given below.

Let's check the washing program

First of all, it is recommended to weed out trouble-free situations. Often there is no breakdown, since by mistake the user turns on a mode that does not involve intensive rotation of the drum. Thus, spinning is not provided for delicate washing and for wool, silk, and down programs.

To confirm your suspicions, you need to remember the selected button and read its description in the factory instructions. Next time, just change the mode or additionally turn on the spin cycle. The second thing we check is whether the spin cycle was accidentally canceled in the standard program.

Important! Don't forget to lock the dashboard, which will help you avoid worrying about accidental switching.

Many modern models allow you to vary the rotation speed of the drum up to its complete cancellation. It’s better to do a test: select a mode, set the push-up to maximum and start the machine again. Wet items will be a reason for further inspection.

Let's look at the laundry in the drum

The spin cycle of a Beko machine often does not work due to an imbalance in the drum. Overload, insufficient loading or uneven distribution of laundry along the walls of the tank leads to imbalance. This problem occurs with older models, since modern machines are equipped with a special function that controls the balance during washing and spinning.

It’s easy to suspect something is wrong: in this case, the unit repeatedly tries to spin up, but to no avail. As a result, the cycle ends 7-15 minutes earlier than the scheduled time, and the laundry remains wet. You can correct the situation as follows:

1. Wait until the hatch is unlocked and open the door.
2. Take out half of the laundry (if there was an overload), unravel the twisted “lump” or add items (if there is a shortage).
3. Close the hatch tightly.
4. Start spinning.
5. Check the laundry for dryness.

Imbalance has a detrimental effect on the shock absorbers, bearing assembly and shaft, so it is best to avoid it. It is important to control the amount of laundry loaded and remember both the upper and lower limits. So, in a machine with a capacity of up to 5 kg, it is necessary to wash at least 1 kg, and in washing machines with a maximum capacity of 8-9 kg - 2.5 kg.

Waste water is not removed

If at the end of the cycle there are not only wet things in the drum, but also a full tank of water, you should pay attention to the drainage system. It is quite possible that the machine simply cannot drain the waste liquid due to a burnt-out pump, a blocked pump impeller, or a blockage in the hoses or pipes. We look for a specific cause and its solution in the following sequence:

1. We disconnect the drain hose from the sewer and probe its length for blockages. If foreign objects are found, unscrew the pipe completely and rinse it under strong water pressure.

Attention! Sometimes the general sewer becomes clogged, so we lower the disconnected end of the drain hose into the sink or bathtub, start the drain or spin mode and wait for the water to flow.

1. We find the drain hatch in the lower right corner of the washing machine body and, using a screwdriver, pry it open. We substitute a container for collecting water and unscrew the garbage filter. Clean the part and the fittings suitable for it. If everything is clean, we test the contacts with a multimeter.
2. We check the integrity of the pump. We free the impeller from wound hair and fur, clean the pump body and measure the amount of resistance present.

The pump and filter cannot be repaired and, in case of breakdown, are replaced with new ones. After all the manipulations, we start the machine for the fastest wash and monitor the drainage of water. An empty drum will eliminate the fault of the drain system.

Hall sensor does not function

Spin does not work even if the tachogenerator is faulty. This device, also called a Hall sensor, is responsible for monitoring the number of revolutions made by the engine and transmitting information to the control board. If it breaks, communication with the module is lost, the system stops receiving information and, for safety reasons, reduces the motor power.

Breakdown is caused by improper operation of the machine, in particular:

• Regular overload of the machine with laundry.
• Prolonged use of the machine without stopping.
• Loose fastenings.
• Loose contacts or damaged wiring.
• Severe voltage surge or short circuit.

First of all, we inspect the wires and, if necessary, tighten the terminals, clean and insulate the conductors. Next, we call the sensor itself a multimeter and evaluate the results. In case of deviations from the norm, we replace it with an analogue.

The motor does not spin the drum

Another situation arises when the engine is not able to accelerate to the required power. For commutator motors, braking is possible when the electric brushes are worn out: washing and rinsing proceed normally, but spinning becomes impossible. If other stages of the cycle are difficult to complete, the engine itself may also break down. The guess is checked in the following way:

1. We disconnect the machine from all communications.
2. Unscrew the back cover.
3. Remove the drive belt.
4. We disconnect all connected places.
5. Loosen the holding fasteners.
6. We rock the motor and take it out of the grooves.

Next, wipe the body with a cloth and inspect for damage. A burnt-out engine has an unpleasant burning smell, stains and charred wires. Then we pay attention to the electric brushes: remove them from both sides of the engine, open them and measure the length of the tip. If it is less than 0.7 mm, you will have to change the pair to a new one. At the same time we call the coils.

Electronic unit malfunction

The worst thing is when the electronics fail. In this case, the triac responsible for spinning burns out, the engine does not receive a command to accelerate and is not able to accelerate the drum. Only a specialist can determine that the reason is in the module, so if you have the slightest suspicion, you should contact the service department.

It is not recommended to repair the module yourself. There is a high probability that a lack of experience, equipment and professionalism will result in the final failure of the board. A replacement part is expensive and it is cheaper to pay for the services of a specialist.

Foreign object in tank

A foreign object caught in the tank also prevents the drum from unwinding. Here it is necessary to react as quickly as possible: a foreign body can damage the walls of the containers and lead to jamming of the entire system. Replacing a tank is very expensive, so at the slightest suspicion it is recommended to stop the machine and remove the dangerous element.

Causes and signs of failure

How to understand that the washing machine does not go into spin mode? Signs indicating a malfunction:

• The program has ended, but the water remains in the drum. No drain.
• You remove wet items from the drum that have not been wrung out.
• The drainage of water is very noisy.
• The water drains normally, but the laundry is not wrung out.
• The spin cycle works every once in a while, the machine does not respond to the set parameters.
• The washer hums as if it is spinning, but it doesn’t.
• The water drains very slowly.

These are the main signs that you should pay attention to if the machine does not switch to spin.

What could be the reasons that the washing machine is broken and does not spin out the laundry completely? There are technical faults that require diagnosis and repair:

1. Problems with the drain pump. If the washing machine has stopped spinning, the drain may not be working, so the water simply has nowhere to go.
2. The level sensor is malfunctioning. If the sensor breaks down, the electronic board does not receive a signal about the amount of water in the tank, and therefore does not send a signal to drain.
3. The control module or its triacs are faulty. Each triac is responsible for the operation of a specific part in an automatic washing machine. Therefore, if it burns out, the board cannot control or issue commands.
4. Malfunction of the electric motor. The brushes could wear out or the wiring could burn out. If there are problems with the operation of the motor, the drum will not rotate fast enough for a high-quality spin. Or the machine will not work at all.
5. The tachogenerator, which controls the number of engine revolutions, does not work. Signs of failure are the same as in the previous case.

READ MORE: TOP 25 best clothes steamers: 2020 rating in terms of price/quality ratio and which one to choose for home use

If a semi-automatic machine without a centrifuge does not spin by itself, then a broken automatic machine shifts this responsibility to you. You shouldn't put up with this. Carry out a thorough inspection and diagnostics of LG, Samsung, Indesit, Kandy and other models of washing machines.

Read on to find out where to start checking.

Beko washing machine does not drain water: reasons, what to do

The Beko washing machine is easy and reliable to use. However, like any other equipment, after many years of work, the machine can fail at the most inopportune moment. If your Beko washing machine does not drain, you can try to solve the problem yourself.

Causes

If the machine does not drain water or spin things out, you should first find out the reason. In this situation, the reasons are divided into two types:

1. Problem during operation:

• clogged drain hose, filter or pipe,
• incorrectly connected hose,
• Wrong choice of washing program.

• breakdown of the pressure switch - the water level sensor in the machine, which is responsible for timely drainage,
• failure of the electronic drain system,
• electric pump failure.

In the first case, you can fix the problem yourself, but in case of a serious breakdown you will have to contact a specialist.

Troubleshooting Yourself

Initially, you should check whether the washing mode is selected correctly. Every Beko washing machine has a cycle that washes delicate fabrics and woollens without spinning. If it is installed, then after washing, you must separately start the process of draining the water. To do this, press the “Start” or “Start” key.

You also need to check whether the drain hose is connected to the machine correctly and assess its condition. If it is too bent or pinched, the water will not drain. In addition, the hose may be clogged with debris. In this case, you should clean it. The length of the drain hose plays an important role when draining water. If a hose longer than 1.5 m is installed, the pump will not be able to pump water over a long distance.

Also, the machine may not drain water due to a clogged filter. In Beko washing machines, the filter is located behind a small protective panel on the right side. You need to remove the filter by turning the holder to the right. Prepare a basin in advance, because water also accumulates in the filter compartment. Afterwards, the garbage disposal must be cleaned and rinsed under the tap.

When using the machine for a long time, the drain pipe also needs to be cleaned. You can get to it from the bottom of the machine, armed with a screwdriver. The pipe is held on by three fasteners that need to be loosened. Having separated the part, we clean it with a small brush, and then install it back. If you find cracks or holes in the drain pipe, it must be replaced with a new one.

https://www.youtube.com/watch?v=zXCf71Ox74Q

To prevent washing machine maintenance, you can also clean the filter installed on the water supply. You can find it on the back panel of the machine, where the hose is attached. Cleaning it prevents the accumulation of sand and rust from tap water.

There is also a drain pump on the back of the washing machine. If the machine hums strangely when washing and refuses to drain the water, then you should pay attention to it. Beko washing machines are equipped with a self-diagnosis function and often detect a breakdown of the pump in the pump responsible for draining the water. And the lit H5 key on the control panel notifies you of this. However, in case of minor failures, the controller does not respond. For example, the impeller in a pump may become loose and fall off, which can be detected by a humming sound. To check the pump, you need to turn on the water drain mode and evaluate the reaction of the impeller. If it does not rotate, then the pump needs to be cleaned or replaced.

How to drain the water yourself

What should I do if pressing the buttons fails to drain the water? You can also do this manually. There are several ways to empty the drum of water:

1. Water can be drained through the hole after removing the drain filter of the machine. To do this, unscrew the filter cover and tilt the machine. Substituting the container, you need to drain all the water and then take out the laundry.
2. If water does not flow through the filter, then the problem is a blockage. It will need to be cleaned.
3. Beko washing machines come with an additional drain hose. So, if the first options do not work, you can run the hose into the drum and drain the water.

Troubleshooting

If the water from the washing machine does not drain, then the reasons, in addition to clogging, may be serious damage. At this stage, it is better to contact professional technicians for high-quality diagnostics and further repairs. There are three main reasons why a washing machine does not drain water:

1. Malfunction in the drain pump . It can be installed on the impeller. As stated above, it will either not move or may even break if overloaded. In this case, the technician will replace the pump with a new one.
2. The problem may also be hidden in the control module . If the control module fails, the signal is not sent from the board and the pump does not begin to drain water. The technician needs to disassemble the machine and fix problems with the programmer.
3. If the drum is frequently overloaded, the water level sensor may fail . The sensor must be replaced, because if it breaks down, it does not detect the water level and sends a signal to the control board to indicate the end of the wash.

There are many reasons why water does not drain from a washing machine, and each of them has its own nuances. It is not always possible to install them yourself, much less repair them. Therefore, it is advisable to contact a specialist. Of course, using the above steps, you can clean the filter and hoses of the machine yourself. If the procedure does not fix the problem, then it’s time to entrust it to a professional.

Source: https://comp-plus.ru/remont/stiralnaya-mashina-beko-ne-slivaet-vodu-i-ne-otzhimaet

When draining

If the Bosch, Ardo, Ariston or Zanussi SMAs stop and do not drain water, the reason must be sought in the drain pump. There may also be a situation when the machine drains the water, but does not spin it out. There may still be some water left in the drum, which is why the spin cycle does not work.

What do we have to do:

• There is a drain hatch at the bottom of the front hull.
• Release the hatch latches and open the door.
• Place the container and remove the filter.
• To check the pump impeller, run the spin or drain mode.
• Shine a flashlight into the hatch hole and check if the impeller is spinning.
• If it does not spin, you need to disassemble the pump.

The drain pipe is checked at the same time as the pump. Depending on the model of the washing machine (“Atlant”, “Whirlpool”, “Veko”, “Gorenye”) you can access the pump through the bottom, front or back of the case. We wrote more about this in previous articles.

• Unclench the clamp of the pipe from the tank to the pump, disconnect it and check for blockages.
• Then disconnect the pump wiring and its mountings.
• Inspect the structure for debris; there may be something wrapped around the impeller.

READ MORE: The CL light is on in the LG washing machine. What is the reason? How to remove? | RemBytTech

If the pipe is clogged, the machine may hum, but not press, trying to drain the water. After installing the parts in place, check the operation of the machine. If the spin does not start again, replace the pump completely.

There is a wash, but there is no spin: why does this happen and how to deal with it - shop All Spare Parts

The washing machine has been working properly for many years, but you began to notice that the last stage of the cycle began to be difficult for it, and the washing machine does not spin out water. Thanks to the spin cycle, clean washed clothes are also semi-dry. This position significantly saves your time on drying things. When the spin function stops doing its job, this indicates, first of all, the need to diagnose the device and eliminate a possible failure in the electronic control. To prevent such situations, it is necessary to deal with the problems that have arisen.

How to avoid breakdown

It is always better to prevent a breakdown than to repair it later. Moreover, the operating rules are simple:

• Before loading laundry into the drum, check all pockets and remove foreign objects.
• Install and connect the machine correctly according to the instructions.
• Sort your items before washing. Place clothes with decorations in special bags.
• Do not load too much laundry. This leads to rapid wear of the washing machine and poor quality washing.
• Install a voltage stabilizer. It will protect expensive equipment from sudden breakdown.
• Clean the drain filter and detergent dispenser periodically.
• Do not close the hatch door after removing the laundry. This promotes the formation of fungus and mold.

Now you know why the drum in a washing machine may not spin and wring out clothes. Be attentive to the first signs of damage, then you will be able to avoid expensive repairs.

READ MORE: Error i30 on a dishwasher: what to do and how to fix it

BEKO washing machine does not spin clothes

The most common question from housewives is what is the reason if the BEKO washing machine does not spin. Here the operating instructions for the washing machine will come to your aid. If this does not help, then you should contact the service center for help from a qualified specialist. Under no circumstances should you climb inside the washing machine yourself, as this can lead to even greater problems in its operation.

What should you do if your BEKO washing machine does not spin?

• » First, check if there is anything in the drum.
• »Secondly, see if the washing program is selected correctly.
• » Third, read the operating instructions carefully.

After all this, if everything works correctly and is configured, you should contact a washing machine repairman. BEKO is the most famous and popular brand on the world market. Even here, there are problems with malfunctions of some parts of the washing machine, which occur over time, since this is an automatic thing and does not require a human factor for its operation.

What to do if the washing machine does not spin clothes?

If your washing machine does not spin clothes, repairing it under warranty will not be difficult. Calling a professional to your home would be the right decision, since a washing machine is quite a large item and is not always convenient to transport. Namely, at home, the master will answer your question: what is the reason and why your machine does not work. A timely contact with a service center for servicing automatic washing machines will prevent the occurrence of other malfunctions that may occur over time. Make the right choice, contact a master, and enjoy the work of your assistant, and undoubtedly she will serve you for many years.

Prices for services

Call the master | Call from mobile

Source: https://ne-otzhimaet.ru/stiralnaya-mashina-beko-ne-otzhimaet.html

Spin does not turn off

Problems with the control module in the washing machine can result in the drum not stopping and the spin cycle not turning off. After such revolutions the car simply freezes. It may also be that the SMA squeezes, rinses, but does not wash. Or vice versa - it washes, but does not rinse.

All these signs indicate problems with the “brain” of SMA, so it begins to work incorrectly.

You can only visually inspect the control board yourself. It is better to entrust basic diagnostics and repairs to professionals.

• Unplug the washing machine.
• Remove the top cover.
• Pull out the dispenser tray. Pull it towards you, pressing the latch in the center.
• Remove the screws securing the control panel.
• Release the plastic latches and remove the panel.
• Release the wiring.
• To remove the board, also release the latches.

If no signs of damage are found on the surface of the board, contact the service center.

Why the Beko washing machine does not spin - the main reasons

This public offer Agreement, hereinafter referred to as the Agreement, defines the relationship between the administrator of the beko-remont.ru domain, hereinafter referred to as the Administrator, on the one hand, and the visitor to the beko-remont.ru website, hereinafter referred to as the Visitor, who accepted this offer to conclude an Agreement by carrying out actual actions to fill out an online form, application or call the contact phone number indicated on the Site, or send an email or application to other contact information indicated on the Site.

Clarifications of terms and definitions

1.1. Administrator’s website – website: https://www.beko-remont.ru.

1.2. Site Service - navigation capabilities, receiving and sending information available for use on the Site by the Visitor.

Subject of the Agreement

2.1. The Administrator provides the Visitor with access to the Site Service, and the Visitor undertakes to use the Service in accordance with the terms of this Agreement.

2.2. The Administrator undertakes to accept information from the Visitor, including requests for repair work.

2.3. The Administrator undertakes to transfer information and requests for repair work received from the Visitor to potential contractors, subcontractors and other persons at the discretion of the Administrator.

2.4. The Administrator is not responsible for the consequences of the resulting relationship between the contractors and the Visitor, including, but not limited to, inadequate quality and content of service, repair and other work.

Other conditions

3.1. The Site, in one way or another capable of causing associative connections in the Visitor with officially registered trademarks, as well as brands, logos and other parts and elements of trademarks, is a random and unintentional coincidence.

3.2. Official copyright holders of trademarks who have noticed similar elements in the content of the Site have the right to contact the Site Administrator for clarification. If agreements are reached, controversial and random associative elements can be removed by the Administrator or modified to the point where the association with the registered trademark is objectively lost.

3.3. This Agreement establishes the complete absence of any relationship between the Site and the official representation of any brand, manufacturing or trading company registered in the manner prescribed by law. The Site is also not an official authorized dealer and/or service center of any registered brand or company, but provides only services for access to the service and functions of the Site, which boil down to the Visitor searching for the best option for receiving repair and maintenance services for his vehicle. he owns household, kitchen and other general purpose appliances.

3.4. Disputes arising between the Administrator and the Visitor may relate exclusively to functional, service and software errors in the structure of the Site and the incorrect operation of its program code. All disputes regarding the quality of repairs or service received by the Visitor are resolved exclusively with the person who provided these services to the Visitor.

3.5. The Parties are released from liability for complete or partial failure to fulfill obligations under the Agreement if the failure to fulfill obligations was the result of force majeure, namely: fire, flood, earthquake, strike, war, actions of government authorities or other circumstances beyond the control of the Parties.

Final provisions

4.1. This Agreement is a document regulating the relationship between the Administrator and the Visitor, as a result of which the Visitor, performing any actual action in the software shell of the Site, including reading content, filling out forms and fields, sending requests and messages and any other actions related to the use of functions and service capabilities The site automatically joins this Agreement in full.

4.2. A hyperlink to this Agreement is located on the main page of the Site, and is available in the form of a pop-up dialog box for easier viewing and reading.

4.3. The Visitor’s refusal to familiarize himself with the text of this Agreement in the presence of actual actions indicating the use of the functionality and services of the Site is considered void, and the Visitor is deemed to have agreed to all the terms of the Agreement on the grounds of actual use of the Site’s capabilities.

Source: https://www.beko-remont.ru/stiralnaya-mashina-beko-ne-otzhimaet-vodu.html