How to hang the door of an Indesit refrigerator?

Reasons for reinstalling the door

14. Other recommendations for repairing the refrigerator door

15. Prevention of door sagging and crack formation

16. Identification and self-correction of seal faults

16.1. Related articles:

Before you learn how to rehang the Indesit refrigerator door, you need to find out why they do it. Work will be required in the following cases:

inconvenient use of the door;
there is any device nearby that does not meet the operating requirements;
personal desire to do something new in your kitchen that will bring originality to the interior.

Getting to know the instructions

Before work, you must read the instructions that come with the equipment. There is usually a description of the steps on how to hang the door of an Indesit refrigerator. When purchased, the doors are on the right side and therefore tips are provided for reversing to the left.

You should inspect the device, find plugs and swivel hinges. Special fastenings must be located on the body. You should start working only after the principle of operation becomes clear.

The nuances of reversing the door with a display

Before you hang the doors of a refrigerator with a display, you need to pay attention to some subtleties. Do not start disassembling the device if there are no holes . There is always a risk of damaging the unit, which will negatively affect the warranty period. You can change the position of the door with the display if the manufacturer has equipped the wires with connectors that allow them to be disconnected from the network.

A device with a display requires careful handling of wires

First, the equipment is disconnected from the power supply , the top panel is removed, and the bolt that secures the top hinge to the body is unscrewed. Remove the wire from the connector and remove the bolts securing the upper loop. The door is lifted slightly and the hinge is removed. Then the loop located in the middle is disassembled. The door is removed. Remove the top cover of the chamber. The cable with the connector is brought out to the side of the case to which the loops will be fixed. When installing hinges, you should look at the instructions, because in different models, including Hotpoint Ariston, Haier, Liebherr, Stinol, Pozis and others, the procedure for carrying out the work may vary.

Then the wire is connected, the top loop is bolted, and the panel and plugs are installed. Using a sheet of paper , check how the door will close.

Tools you'll need

Naturally, it is unlikely that you will be able to complete the above task with just a screwdriver and pliers. For comfortable and efficient work, it is recommended to acquire the following tools:

screwdriver,
set of open-end wrenches,
hexagon set,
set of sockets with ratchet.

Note that if the refrigerator is two-chamber. It is quite possible to rehang only one door if the surrounding space requires it. Although the majority still performs full re-weighting.

The only difficulty that may arise with modern models of Indesit refrigerators is that they have a display that is located on the facade. Therefore, after dismantling the door, you will need to re-route the cables.

How to rehang doors with a display

The operation of the display is ensured by connecting cables that run through the top mount. If the design of the unit involves reinstalling the doors, the wires are disconnected from the connectors. To flip the display refrigerator door from left to right, follow these steps:

Remove the decorative strip, if provided for by the design of the device.
Remove all top hinge fasteners. After this, the part is removed, the door is dismantled, lifting it.
Remove the top part of the refrigerator body. This helps to gain access to the electronic unit. The wire with the connector is led out through the opposite hole in the panel, equipped for this purpose.
Move the loops. The procedure will be the same as when rehanging the doors of a device without a display. Before starting work, it is recommended to carefully study the instructions. Installation may cause some difficulties due to the design of the hinges.
Connect the display wire to the connector removed from the corresponding hole in the control unit.
Secure the hinge by tightening the bolts. After this, you need to check that the display is connected correctly and the door is installed correctly.

Preliminary preparation

Before you begin the procedure of re-hanging the refrigerator doors, you need to make sure that it can, in principle, be carried out on this model. You can find out about this by reading the operating instructions. In cases where the instructions cannot be found for one reason or another, it is necessary to carry out a simple visual inspection. There should be identical technological holes on the opposite side of the hinges. If you couldn't find them, forget about this idea. You cannot re-hang the doors on your refrigerator model.

If there are symmetrical notches and holes on the opposite side of the hinges, we proceed to the rehanging procedure. First, you need to empty the refrigerator of food and disconnect it from the electrical network. The reinstallation itself can be carried out only after the refrigerator is completely defrosted. If this requirement is neglected, you may end up with a loose fit after re-hanging.

Re-hanging instructions

Before re-hanging the refrigerator doors, the appliance is disconnected from the power supply. Cells are cleared of products, shelves and trays.

How to remove

You need to start work by dismantling the top door. This is done as follows:

The door is attached to the body with masking tape. This prevents the part from falling during dismantling.
The hinges, screwed with two bolts, are removed first. The fasteners are unscrewed with a wrench. The hinges can have different configurations, the method of dismantling depends on this.
Remove the plugs covering the installation holes on the other side. The loop will be installed at this location. To avoid damaging small parts, the plugs should be removed carefully using a flat-head screwdriver.
Remove the decorative trims located on the front of the door. The screws are unscrewed, after which the panel is pryed up with a flat-head screwdriver and removed.
Remove the top cover of the refrigerator. Some appliances are designed in such a way that it will be impossible to remove the door without completing this step. Unscrewing the fasteners, remove the cover and put it aside. It is recommended to place all fasteners in a container.
Dismantle the panel. This step is necessary to ensure that the fasteners can be removed. The type and dimensions of the parts depend on the model of the refrigeration unit. After unscrewing the bolts, remove the top hinge.
Remove the handle. Before removing this part, remove the decorative trims. If the handle is not secured with screws, it cannot be removed. The design in this case already implies the possibility of reversing the door.
Removing the door. After removing all fasteners, peel off the masking tape. The door is lifted, separated from the middle hinge, and then removed to the side. The previously removed plugs close the empty holes.

After completing the above steps, you need to rearrange the lower door. To do this, perform the following steps:

Use masking tape to secure the door to the body;
dismantle the middle loop by removing the rubber seal from the pin;
remove the tape, then, lifting the door, remove it from the bottom hinge, remove it and put it aside;
remove the plugs located in the middle of the side of the refrigerator body (the removed hinge will be installed here);
insert plugs into the holes remaining after removing the loop;
remove the bottom hinge remaining after dismantling the refrigerator door (using suitable tools, remove the pins and bolts holding the part);
The resulting holes after removing the loop are closed with plugs.

After dismantling is completed, all removed parts are installed in a new location.

How to transfer loops to the opposite side

When rearranging parts, you should not make any changes to their design. This may cause problems with the installation and operation of the door. Incorrectly placed hinges contribute to sagging of the element. The installation procedure includes the following steps:

The lower loop is installed in the place opposite to the original position. The bolts are tightened using a wrench or a screwdriver.
Install the rubber seal and the lower pin. Work may be complicated by the lack of holes on the left side of the case.
The lower door is placed in the required position and secured with masking tape. Instead, you can tilt the body of the device back. This way the door will be better held and not move when fixing the fasteners.
The middle hinge pin is placed on the bottom door pin. The holes are aligned with the installation locations on the case and the screws are screwed in. The top door is installed in the same way.
Mount the top hinge, tightening the screws securely.
Install a decorative strip. After this, the pin of the upper hinge is inserted into the sleeve of the corresponding door. The part is fixed with bolts that are tightened with a screwdriver or wrench.

Having rearranged the hinges, you need to check the correct installation. To do this, open the doors and insert paper between the body and the seal. After closing the device, they try to pull out the sheet. If it comes out easily, the door is not installed correctly. In this case, the hinges will need to be aligned by loosening or tightening the bolts.

Removing the decorative strip

Using a Phillips screwdriver, unscrew the so-called. mask - a plastic panel covering the top hinge of the refrigerator door, and remove it by slightly pulling it towards you. Under this panel there is a thermal insulating layer of foam. This material crumbles and breaks quite easily, so during all work on hanging the door it must be carefully removed and put aside so as not to damage it.

Once the decorative plastic panel is removed, it becomes possible to remove the fastening of the top hinge, which is a bar with a pin that holds the door in place. A similar strip with a thread for a pin is present on the other side. The bolts of the strip are unscrewed with a hex key or wrench. In principle, while the top hinge is unscrewed, the door can be held on by the seal, but just in case it is additionally secured with tape.

Next, the door of the freezer (if it is a two-chamber refrigerator) or the entire refrigerator (if it is a single-chamber one) can be removed. To do this, open it wide and lift it up from the lower fastening, carefully holding it so as not to bend the fastening in the process.

If the refrigerator is two-chamber, i.e. In addition to the refrigerator itself, there is also a freezer compartment at the top, then in addition to the hinges at the top and bottom there will be another one in the middle between the doors of the two compartments.

When the freezer door is removed, access to the bolts of this middle hinge becomes quite convenient. Remove the decorative caps from them in the color of the refrigerator and unscrew them. Then, as with the freezer door, the refrigerator door is opened, lifted, and removed from the bottom mounting. After which it becomes possible to dismantle the lower hinge.

If the refrigerator is old enough, then perhaps the sealing rubber on it has already become unusable, ensuring the tightness of the refrigerator chambers. Since the doors are removable anyway, replacing or at least repairing the seal may be a good idea.

The bottom hinge is also hidden under a decorative strip that must be carefully removed. After this, you can unscrew the loop from one side and move it to the other, and then put the decorative strip back in place.

While the doors are removed from the refrigerator, it is convenient to rearrange the handles on them. To do this, remove the upper part covering the fasteners, unscrew these fasteners, attach the lower part on the opposite side and snap the upper part again.

Step-by-step instructions for rehanging

How to remove

If you are the owner of a two-chamber refrigerator with two doors, then it is better to start the dismantling process from the upper facade, and then move on to the lower one. The procedure is as follows:

Remove all plastic plugs from the device (including the side on which installation is planned).
Secure the top door with masking tape. Make sure it is held firmly and will not fall.
Unscrew the bolts from the hinges, if necessary, first remove the decorative trim and handle.
After unscrewing all the bolts, carefully remove the hinge, peel off the tape and, lifting it a little, dismantle the door.
Secure the lower part with tape in the same way.
Remove the seal from the pin and tighten the fastening of the middle and then the lower loop with a wrench.
Remove the tape, remove the door, and move it to the side.
Place the removed plugs in the free spaces.

At the bottom of the article there will be detailed video instructions, if you have any questions, we recommend that you read it.

How to transfer

When transferring loops, it is important to adhere to a strict sequence of actions, performing work in a mirror order, without introducing changes. Any inaccuracies may affect the quality of assembly and subsequent operation of the device.

Installation is carried out as follows:

Attach the bottom hinge to the desired side using tools.
Install the rubber seal and pins.
Secure the lower facade in the required position with masking tape.
Place the middle hinge pin onto the door pin and secure it with screws.
Similar steps for mounting the top part.
Secure the connection with screws.
Reinstall the decorative trims and plugs.

Assembly and adjustment

After installing all the elements, you need to check the correct installation and tightness of the refrigerator, whether it closes tightly. This can be done using a piece of paper inserted between the door and the body. If the sheet comes out without effort, an error was made during assembly. Try adjusting the fasteners by tightening or loosening the tension.

If doors with display

Not every device with a display has the ability to change the door position, so you should first read the technical instructions. This work requires some experience and dexterity, so if you are not confident in yourself, contact the nearest service center for the manufacturer's household appliances.

For the functioning of the electronic screen, a cable of wires is attached to it, passed through the top loop, and there is a corresponding connector for disconnection. After disconnecting the device from the network, perform the following manipulations:

Remove the decorative trims and top mounting bolts.
Remove the disconnected cable.
Disconnect the hinge fasteners and remove the refrigerator doors.
Disconnect the device located on top of the cover and route the connecting cable through the opposite hole.
Transfer the fastener to the opposite side according to the instructions.
Connect the wires to the connector.
Reinstall the housing covers and decorative panels with plugs.

Features of outweighing from popular manufacturers

Atlant

From the Atlant brand unit, you first need to remove the decorative panel and unscrew the fasteners with a screwdriver.
By pulling the bar towards you, you will find foam insulation, which must be carefully removed without breaking.
Then twist the top loop with a hexagon.
Dismantle the middle one completely.
Disconnect the door and lift it up to remove it.
Release the lower fastening from the lining and twist it.
After these steps, transfer the loops to the opposite side.

Some models may be missing the bottom left hole for one screw. You can drill the hole yourself or buy the appropriate part.

Samsung

Re-hanging the facade of a Samsung refrigerator with your own hands is done in a standard way. First, the contacts located under the cover are disconnected, then the loops are transferred and the display wires are assembled.

Don't forget to move the guide bracket and the freezer opening stop.

Indesit

To move the Indesiat refrigerator door, make sure that the design allows for these manipulations and that all the necessary elements are included in the package. It is convenient that the opening sensor is located in the center and does not need to be rearranged.

Bosch

It is easy to reinstall the Bosh refrigerator door itself: you just need to strictly follow the procedure specified in the technical data sheet. Initially, you need to remove the fastening plugs, twist the fasteners and disconnect the hinges and handle. These elements are immediately installed on the other side.

Difficulties may arise when working with equipment equipped with a display, so it is important to record all the manipulations performed so as not to miss anything.

Give yourself access to the cables, carefully disconnect the contacts.
After this, you need to remove the camera door and the panel itself that masks the wires.
Then, twist the loop, transfer the contacts and assemble everything in the reverse order, checking the notes made.

Ariston (Hotpoint-Ariston)

It often happens that the Hotpoint-Ariston kit does not include the necessary plastic inserts. Craftsmen simply replace the upper loops with the lower ones. It is also worth paying attention to the opening indicator sensor, which needs to be moved to the appropriate side.

LG

The doors of LG brand refrigerators are attached using special hinges, the dismantling of which is carried out using a screwdriver or screwdriver of the required size. It is first necessary to strengthen the structure with masking tape so as not to drop or damage the door. Actions are carried out carefully and carefully, because any bending or deformation will render the spare parts unusable.

The electronic display wires should be turned in the opposite direction and hidden under the panel and trim.

How to rearrange the door on the refrigerator? Instructions

First of all, find out whether the design of your refrigerator allows for door relocation. This information is usually contained in the instruction manual. Do you remember where you hid this document? Then look for plastic plugs on the refrigerator body - a spare unit for fastening the doors.

If it is there, then rearranging the doors is possible. In addition, the instructions usually contain detailed guidance on how to rehash the refrigerator doors to the other side specifically for your refrigerator model. Follow it if you manage to find it!

Couldn't find a door reversal guide specifically for your refrigerator model? Then read on. Below we present the general sequence of actions for rehanging the doors of a classic two-chamber refrigerator with electromechanical control. Re-hanging details may vary for different brands and models of refrigerators.

1. Prepare the necessary tools. You will need a flathead and Phillips screwdriver, a wrench (the size depends on the make and model of the refrigerator) and masking tape.

2. Unplug the refrigerator from the outlet. Before you begin, it’s a good idea to make sure that the refrigerator is unplugged.

3. Secure the door with masking tape. Using masking tape, attach the refrigerator door that is removed first (in most models, this is the top door) to the body in several places

4. Unscrew the top hinge of the refrigerator. Using a screwdriver, remove the plugs, unscrew the bolts (using a wrench or screwdriver) and remove the top mount. On some refrigerator models, you may need to remove the top panel (refrigerator cover) to get to the top hinge bolts.

5. Remove the top door. Remove the masking tape while holding the door to prevent the hinge from becoming deformed. Then, carefully lift the door up, remove it from the bottom pin of the middle hinge and set it aside.

6. Move the top door mounting plugs to the other side. Armed with a screwdriver, remove the plugs on the opposite side of the case and move them to the vacated slots.

7. Remove the middle hinge of the refrigerator doors. To do this, first secure the bottom door of the refrigerator with masking tape to the body of the refrigerator. Then, remove the spacer from the pin and use a wrench (or screwdriver) to unscrew the middle hinge.

8. Remove the bottom door. Remove the masking tape, carefully lift the door, remove it from the bottom pin and set it aside.

9. Rearrange the middle hinge plugs. Using a screwdriver, release the middle hinge mounting slots on the opposite side of the refrigerator body. Replace the plugs in the vacated holes after removing the door.

10. Remove the lower fastening of the refrigerator door. Pull out the pin and use a screwdriver to disassemble the bottom door fastener (some refrigerator models may require a wrench).

11. Install the lower door mount on the other side. Remove the plugs and move them to the opposite side. Then, install the bottom hinge on the other side in a mirror projection and secure the pin to it.

12. Move the refrigerator door fastening elements on the doors themselves to the opposite side. To do this, you will need to dismantle the fastening elements (bushings, pins, etc.) using a screwdriver or wrench, replace the plugs on the opposite side of the doors (if any) in their place, and install the fastening elements in the holes freed from the plugs.

13. Reinstall the refrigerator door handles to the other side if the design of the refrigerator requires it. To do this, carefully, so as not to scratch, pull out the plugs on the surfaces of both doors and release the sockets for the bolts. Door handles will be attached in these places. Then, using a screwdriver, remove the handles from both doors of the refrigerator, and install the plugs in the slots vacated after removing the handles.

Install handles on the opposite side of the refrigerator and freezer doors.

14. Place the bottom refrigerator door onto the pin. Use caution when doing this.

15. Secure the middle loop. Holding the bottom door of the refrigerator (you can also secure it with masking tape), thread the bottom pin of the middle hinge into the sleeve on the refrigerator door, align the holes on the hinge with the holes on the refrigerator body, and using a wrench or screwdriver, secure the middle hinge in a mirror image to its previous position.

16. Place the top refrigerator door onto the pin. First, return the gasket to the top chamber door pin, and then carefully push the door back on. To be on the safe side during this stage, you can secure the door to the refrigerator body with masking tape.

17. Screw the top hinge in a mirror projection. Install the top mount of the refrigerator so that its pin fits into the sleeve on the door, and the holes for the bolts coincide with the holes on the unit body. Use a screwdriver or wrench to secure the hinge.

18. Check the tight fit of the doors to the refrigerator body. This can be done using a thin strip of writing paper. Place it against the refrigerator body and close the door. Pull the edge of the strip and try to pull it out. If it pulls out freely, it means the refrigerator door needs to be adjusted. Perform a strip test along the entire perimeter of each door.

19. Adjust the refrigerator doors (not all refrigerator models provide this in the design of the hinges!) if, after rehanging, they do not fit tightly. This can be done using adjusting bolts at the top, middle and bottom fastening points of the refrigerator doors.

To enhance the fit, tighten the bolts clockwise. If the doors fit too tightly and open with force, the adjusting bolts should be loosened slightly by unscrewing counterclockwise.

How to hang the refrigerator door yourself (step-by-step instructions)

Before hanging the refrigerator doors, unplug and remove food from the shelves. In two-chamber models, re-hanging begins from the top door. To prevent it from falling during disassembly, it is attached to the body with tape in several places. The door is held on hinges that are screwed with 2 bolts. They are removed using a flat screwdriver, having previously removed the plastic plugs that cover the holes on the side where the removed loop is to be screwed. Use a Phillips screwdriver to release the decorative panels .

There are models of units in which access to the hinge at the top is required to dismantle the door. To do this, remove the top cover of the refrigerator. All removed elements should be put in a separate place.

After unscrewing the bolts of the top hinge , dismantle it, remove the plugs, and remove the top handle. The handle, which is not bolted, is not touched. It is already arranged so that the door can be rearranged.

After unscrewing the bolts and removing the hinges, remove the tape and remove the top door . To do this, lift it, separating it from the middle loop. The door is pushed aside. You need to throw the removed plugs into the empty spaces of the sockets on the opposite side.

Then remove the bottom door , also fixing it to the body. Remove the gasket from the pin and remove the middle loop with a wrench. Remove the tape, slightly lift the door from the lower pin and release it. They put it aside.

The bottom door in two-chamber refrigerators is removed after the top

Next, remove the plugs from the middle holes of the refrigerator in order to dismantle this loop for rearranging them into the resulting holes. The lower hinge is disassembled using a screwdriver or wrench. Remove the mounting bushings, pins, and unscrew the screws that hold it in place. After removal, plugs are inserted into the holes on the other side of the housing.

After disassembly has been completed, all dismantled parts are transferred in the reverse order, starting from the bottom door. The fasteners do not change. The bolts are tightened with a screwdriver or wrench, and the lower pin and gasket are installed. The lower door is installed by first moving the handle to the opposite side onto the pin, which is secured with tape.

Next, secure the loop in the middle . Its lower pin is put on the bushing in the lower door; you need to make sure that all the holes on the body and hinge coincide. The loop is fixed with screws. Afterwards, the upper door of the device is also installed on the pin of the middle hinge, attaching it with tape. upper hinge pin is placed in the sleeve on the upper door , aligning the holes, and secured with bolts using a wrench or a screwdriver. The new door is checked for leaks.

Place a strip of paper against the body, close it and check how it is clamped. Pull the paper, if it comes out easily, you need to adjust it.

In two-chamber models, the doors are installed on separate hinges. Replacement is carried out in the same sequence, but for each sash there are two fastenings instead of one in the middle. If possible in a 2-chamber unit, you can hang one door. In a kitchen where there is not much space, such a weight makes using the appliances much more comfortable .

In single-chamber refrigerators , for example, Biryusa, re-hanging is more difficult. First, remove the top panel, under which there is a hinge mount. The latter is removed, then the same is done with the panel and the loop located below. Not on all devices you can change the door opening yourself.

Removing the lower door

After this, we begin the lower dismantling. We use the same masking tape to secure it on the side.

We remove the plastic spacer from the middle fastening pin and, using a wrench or an appropriate screwdriver, unscrew the middle hinge.
Carefully holding the bottom door, remove the masking tape from it and, slightly lifting it, remove it from the bottom mounting pin. After this, set the bottom door aside.
On the opposite side, use a screwdriver to remove the plastic plugs and move them to the newly freed side.
Using a screwdriver, disassemble the lower mount and remove the mounting pin from it.
We remove the lower plugs and then move the pin to the opposite side, having previously secured the lower loop in the new place.
After all the fasteners have been swapped, we hang the doors on them. First the lower one, and then the upper one in reverse order.

Finally, check the tight fit of the doors to the refrigerator body. To do this, carry out a visual inspection of the contact area and, if large gaps are found, adjust the fit using fastening bolts. After all the cracks have been eliminated, check the tightness of the fit using a thin sheet of paper. The sheet is placed between the door and the refrigerator body and then the door is closed. If the fit is tight enough, the sheet will be impossible to remove and will tear in half, which indicates a perfect fit. Otherwise, if the sheet is easily removed from the contact slot, it is necessary to adjust the tightness of the fit using the fastening bolts.

How to rehang refrigerator doors yourself without resorting to the services of a specialist

Almost all modern refrigerator models have a pre-designed option for reversing the doors.

And as a rule, this procedure is carried out by employees of a specialized store at the request of the buyer immediately at the time of purchase of the unit.

But the need for reweighing may arise after the purchase, and, moreover, when the warranty on the device has already expired. In this case, you will have to act independently, using the necessary tools available in the house and the appropriate skills of a home craftsman.

The need for reweighing may arise due to a number of objective reasons , namely:

During operation, it suddenly became clear that it is more convenient for the owner to open the refrigerator in a different direction than in the one provided in the factory version.
The kitchen was remodeled, and after that it became inconvenient to open the refrigerator in the usual direction.
After several years of operation, the seal lost its elastic properties, the fastenings became old and sagged. As a result, the door no longer fits tightly, and the refrigerator partially lost its seal. In this case, simply reversing the door to the other side can help correct the situation.

Preliminary preparation

In cases where the instructions cannot be found for one reason or another, it is necessary to carry out a simple visual inspection . There should be identical technological holes on the opposite side of the hinges.

If you couldn't find them, forget about this idea. You cannot re-hang the doors on your refrigerator model.

symmetrical notches and holes on the opposite side of the hinges

First, you need to empty the refrigerator of food and disconnect it from the electrical network. The reinstallation itself can be carried out only after the refrigerator is completely defrosted.

If this requirement is neglected, you may end up with a loose fit after re-hanging.

Set of tools

To work we need a simple set of tools:

Wrench. The size is determined by the specific brand of refrigerator.
Two screwdrivers. One is flat, the second is cross.
Masking tape.
A thin piece of paper.

Sequence of reweighing stages

It must be said right away that it is much easier to rearrange the doors on double-chamber refrigerators than on single-chamber refrigerators. In the latter case, you will have to at the same time .

Removing the top mount

Before starting, we secure the door on the side with masking tape so that during the dismantling process it does not accidentally fall to the floor.

Using a screwdriver, remove the plastic plugs from the mounting holes.
We unscrew the bolts of the upper hinge and dismantle the upper fastening.
After this, it is necessary for someone from your household to actively help you, namely, to hold the already half-dismantled door. The adhesive tape may not hold up, and the door may simply break the bottom fastening under its own weight.
Peel off the masking tape, lift the top door and remove it from the bottom mounting pin. After this, set the upper door aside.
The upper plugs are moved to the opposite side, into symmetrical technological holes.

Removing the lower door

After this, we begin the lower dismantling. We use the same masking tape to secure it on the side.

We remove the plastic spacer from the middle fastening pin and, using a wrench or an appropriate screwdriver, unscrew the middle hinge.
Carefully holding the bottom door, remove the masking tape from it and, slightly lifting it, remove it from the bottom mounting pin . After this, set the bottom door aside.
On the opposite side, use a screwdriver to remove the plastic plugs and move them to the newly freed side.
Using a screwdriver, disassemble the lower mount and remove the mounting pin from it.
We remove the lower plugs and then move the pin to the opposite side, having previously secured the lower loop in the new place.
After all the fasteners have been swapped, we hang the doors on them. First the lower one, and then the upper one in reverse order.

The sheet is placed between the door and the refrigerator body and then the door is closed. If the fit is tight enough, the sheet will be impossible to remove and will tear in half , which indicates a perfect fit.

Otherwise, if the sheet is easily removed from the contact slot, it is necessary to adjust the tightness of the fit using the fastening bolts.

Refrigerators with display

Some modern models have a refrigerator control module built into the door. The operating procedure in this case does not change. The only peculiarity is that you will need to transfer several wires connected into a single cable to the other side. To do this you need:

Remove the top cover of the refrigerator body.
Find the tight wiring harness and disconnect them. As a rule, in this place there are special terminals in all wires. Therefore, it is quite easy to separate them. Difficulty may arise during the reverse connection. In order not to confuse where to connect which wire, draw a diagram of the connection or take a photograph before starting to disconnect.
After removing the door of the upper chamber and dismantling the cover in which the wires are located, transfer the wires to the other side and remount everything in the reverse order.

If your refrigerator is still under warranty , then the best option is to invite a specialist who will do this seemingly simple job in the shortest possible time, and most importantly, competently and skillfully. Otherwise, if after some time the need for more serious intervention arises, you will not be able to use the free services of service center specialists.

Source: https://220v.guru/bytovaya-tehnika/holodilniki/kak-perevesit-dver-holodilnika-indezit-i-ne-tolko.html

How to rehang the doors of a refrigerator with a display yourself?

The sequence of actions when reversing the door in an electronically controlled refrigerator is generally similar to the procedure described above for electromechanical models. But there is one important point that needs to be given special attention.

In two-chamber electronically controlled units, a cable runs to the display through the top hinge of the top door (usually the refrigerator door). When rehanging the door, you need to “throw” the cable to the opposite side. For this:

Using a screwdriver, unscrew the screws and remove the refrigerator body cover. Under it there are cables of wires.
Use your hands to disconnect the wiring harness that goes inside the door from the rest of the wiring.
After removing the upper chamber door, remove the wire cover on it (located at the top of the door) using a flat-head screwdriver.
Disassemble the loop through which the wiring harness enters the door and transfer the cable to the opposite side of the door.
Assemble the hinge on the opposite side of the door in the reverse order compared to disassembly.
Cover the wires with the door cover.
Once the top compartment door is in place, connect the wire harness to the rest of the wiring and cover the wires with the refrigerator body cover.

Different brands and models of refrigerators have their own nuances for rehanging doors.

How to hang a refrigerator door: tips for beginners

Practice shows that most models of refrigerators presented in stores and shopping centers have the door on the right side. In real life, such an arrangement is not always the most optimal and forces owners to redo the layout or look for a new installation location for the refrigerator.

In fact, many modern models from the factory provide the ability to hang the door on the opposite side. Most often, Indesit, Atlant, Stinol and Samsung refrigerators have this option. As a rule, this opportunity is an integral part of warranty service, and, as is known, it has a certain period.

Among other things, there are often situations when during the warranty you took the opportunity to rehang the door, and now you have decided to return everything to its original position. Don’t despair, because you can solve this problem yourself and hang the door with your own hands.

It's no secret that the process of hanging doors on a two-chamber refrigerator is not difficult. First of all, the door is rearranged on the refrigerator compartment, and then on the freezer. As for single-chamber units, the situation here is much more complicated.

First of all, it is worth considering the fact that when reversing the door to the other side, you will need to replace the freezer door. Among other things, it is not always possible to figure out the design of convex handles on your own. That is why it is better to ask a specialist for advice.

How to rehang a door?

The next pitfall will arise if the refrigerator door does not fit tightly. There is a misconception that if you move it to the other side, this problem will disappear by itself. But this is far from reality.

The reason lies in the wear of the rubber seal that runs along the entire perimeter of the door. If you ignore this warning and do not replace the seal, even after “throwing” the door the problem will not disappear.

If everything is fine with the rubber band and the problem lies in deformed fasteners, then, indeed, moving the door to the other side will completely solve it.

Removal process

How to hang a door with your own hands?

If you have made the final decision to move the door of the refrigeration unit to the other side, before starting the main process, you should do some preparatory work.

In this case, we are talking about disconnecting the power supply, dismantling all shelves, drawers and magnets, as can be seen in the photo, as well as choosing a suitable screwdriver, wrenches and knife.

When everything is ready, you can start rehanging, following the step-by-step instructions:

First of all, you need to find out whether the manufacturer provides for reinstalling the door to the other side on your model of refrigeration unit. This is quite easy to determine. On models where the factory allows the door to be hung, special holes can be seen on the opposite side of the body and door.
When all doubts have disappeared, you can begin dismantling the door. To do this, you need to remove the corresponding fastenings from the unit, then, carefully holding the door, unscrew the screw. When this stage is completed, the door can be placed near the nearest wall, or simply placed on the floor.
One by one, remove the rotary hinges from one side of the door and install them on the other, closing the resulting holes with decorative plugs. Experts strongly recommend rearranging hinges only as a complete set, without changing their elements among themselves. The fact is that each loop already has a certain output, which means that if you rearrange small elements from one loop to another, you can achieve an extremely negative result.
Once the hinges are reinstalled, the door can be hung in its rightful place and screwed to the refrigerator body using screws. First of all, the upper loop is secured, and only then the lower one. This approach will minimize the risk of damage. After fixing both hinges, it is necessary to adjust them.
The final step is to reinstall the door handle.

Important to remember!

In order to reinstall the refrigerator door to the other side without involving specialists, you should carefully study the manufacturer's instructions. The fact is that many refrigerator models have a number of individual features that require attention. For example, there are times when in order to re-hang the door you will have to move the opening sensor.

This indicates that you should check in advance for the presence of a corresponding hole on the opposite side of the door or frame. Among other things, for some models, rearranging the door requires the use of some additional elements, which, in most cases, are supplied in the kit.

As for models that have an electronic display, such as in Atlant, Samsung, Indesit or Stinol refrigerators, it is best not to try to hang the door yourself, but to seek help from professionals.

The fact is that when performing work, you will also need to reposition the control cable.

If you do not have the appropriate skills, you can accidentally damage the cable, and this will definitely lead to extremely undesirable consequences and forced repairs.

In conclusion, experts give all beginners one simple piece of advice. When installing the door, tilt the refrigerator slightly backwards. The door will close on its own and its adjustment can be made much faster and easier.

It is important to take into account the fact that if you decide to independently move the refrigerator door from one side to the other, you automatically refuse the warranty and service provided by the manufacturer.

If no difficulties scare you, and you are ready to do all the work yourself, watch the instructional video and feel free to start hanging the door.

Source: https://tehnika.vyborkuhni.ru/sovety/perevesit-dver-holodilnika

Installing the door on the opposite side

It is necessary to install the hinges before hanging the door of the Indesit refrigerator. The instructions include the necessary rules for performing quality work. First, the plugs are removed and the canopies are attached to the holes. You should not immediately tighten the bolts tightly, because the position of the structure may need to be adjusted.

If there is a closing sensor, it also needs to be rebalanced during operation, and for this you need to take care of installing the fasteners. When it is located in the center, no rearrangement is required. There may not be a sensor, since in some devices it is located inside the unit, under the casing. This also applies to the light bulb switch: it is often mounted internally, which means rearranging is not required.

Hinges should have guide pins, so installing them in a new location will be very simple. But it also happens differently - the pins are located on the door, which determines the sequence of actions. Canopies can also be adjusted in height. First you need to install the lower hole, and then the upper one. They are secured with bolts.

The door must be adjusted by checking the quality of the seal. How to rehang the doors of an Indesit refrigerator so that everything is done securely? A level is suitable for this, but you can compare everything visually. It is necessary to measure all parameters and adjust shortcomings. When the door is re-hung, the refrigerator must be tilted back slightly. Once the door is opened, adjustments can be made faster.

Changing the position of the handle

If the handle is made in the form of a housing element (pressed inward), then you won’t have to do anything. But usually handles consist of two parts, one part is attached to the door and carries the load, and the second is a decorative trim. If you need to move the handle on the top of the door, you will have to reattach the harness going to the display. There should be another hole for this in the upper part of the door - it will be closed with a plug. Disconnect the connector with the wires, pull the harness through the new hole and secure the wires to the door.

The handle is removed using a screwdriver, and plugged holes are provided on the door for a new fastening. It is enough to remove the handle, remove the plugs in the new place, and screw the handle back on. All old mounting holes (both for handles and door hinges) are closed with plugs.

Adjusting awnings

Just moving the doors from the left to the right (or vice versa) is half the battle. They must be adjusted so that the door sealing tape fits snugly against the unit body. Lack of tightness of the refrigeration and freezer chambers will lead to overheating of the compressor, and, as a result, to the breakdown of a useful household appliance.

A skewed door can also lead to damage. This problem may have occurred when the guide hinges were repositioned. We check the fit of the seal and, if necessary, carry out mini-repairs of the rubber band.

We tighten the “stuck” bolts and use them to adjust the vertical and horizontal position of the door - the distance between the top line of the door and the top of the body should be equal to the distance between the line of the bottom of the door and the bottom of the body.

Tip: when the door is already hung, tilt the refrigerator body slightly towards the wall - in this position the door will lie on the body and it will be easier and easier to adjust.

Two-chamber refrigerators Indesit and Atlant: how to rehang the door according to the instructions

Choosing a refrigerator for a modern kitchen is a responsible matter.

It is necessary to provide for a lot of seemingly insignificant details that can subsequently affect the ease of use of the unit: appearance; dimensions (width, height, depth); capacity (total volume, V of the refrigeration and freezer compartments); number of compressors; location of the freezer and refrigerator compartments; energy efficiency; dimensions, material and color; types of management; defrosting systems and installation types; the ability to adjust door hinges and the ability to move them from one side to the other.

It’s the latter that we’ll “talk” about in this article, or more precisely, about how to change the door opening side of the Indesit and Atlant refrigerators.

Work algorithm

To rearrange one or two doors on an Indesit refrigerator, you will have to perform a number of simple operations if you have experience with tools such as:

screwdrivers - figured (phillips) and slotted (flat);
screwdriver;
booster knob or ratchet;
wrenches – open-end wrenches and hexagonal ones.

The need for all or part of these tools when rehanging the refrigerator door will depend on the components used in the specific Indesit technique.

Attention! Before you begin work on re-hanging the doors, make sure that the unit, disconnected from the power supply, has thawed and that the rubber seal around the perimeter of the door has no defects and is completely straightened.

This is important for subsequent adjustment of the tight fit of the doors to the refrigerator body in a new, overhanging position. And remove products from the shelves!

Removing the door

All Indesit refrigerator doors are attached in the same way - on rotary hinges. The hinged canopies themselves are possible with some variations in the arrangement of bolts and nuts - hardware.

The step-by-step procedure for freeing doors from hinges is as follows:

Using a knife or slotted screwdriver, remove the decorative plugs under which the hardware is located.
We select the necessary tool (wrench or screwdriver) to the slot on the bolt head.
Loosen the fastening of the lower rotary hinge.
Loosen the top one.
Unscrew the bolts of the lower canopy completely.
Holding the door, pull out the unscrewed bolts.
Remove the door from the top canopy by lifting it up.
We set aside the removed door.

Fastening the door to the back side

On the other side of the case there are plugs, the same as those used to cover the hardware in the first case. Sometimes they are replaced by a common plate.

It is necessary to attach hinges (canopies) to this place for re-hanging.

We follow the instructions:

We remove the plugs.
We find pockets with threaded threads underneath them.
We insert the guide pins of the canopies (loops) into the pockets.
We first place the lower part of the door on the pin and “grab” it with the bolts we removed earlier.
We insert the upper guide (upper pin) into the upper hole of the door and secure it, but not all the way.
All that remains is to adjust the height of the hinges.

Important! If the guide pins are not on the hinges, but on the door itself, we do not change the sequence of actions!

Tip: when the door is already hung, tilt the refrigerator body slightly towards the wall - in this position the door will lie on the body and it will be easier and easier to adjust.

Doors and displays

How to rehang the Indesit refrigerator door if there is a display adjustment panel above the door? The question is not idle, because The thin machine is easy to break if handled roughly.

Under the upper horizontal door of the refrigerator there is a shield - a false panel, where the electrical cable system that powers the display is located. In order not to damage the system, you must carefully remove the shield using a screwdriver and loosen the tension on the cable assembly as much as possible so that they do not break when manipulating the doors.

See if it is possible to disconnect the panel wires from the general power system using a connector. If it is possible to remove the shield along with the display panel, do it!

After re-hanging the door, return the shield and panel to their place, connecting the connectors.

After adjusting the height of the door and the tightness of its fit to the body, connect the device to the network. If the refrigerator started working, the light appeared, and it became noticeably colder inside both chambers, then everything was done correctly and the refrigeration unit is ready for further use.

Why is the transfer option important?

When buying a refrigerator, people expect long-term use of the unit, at least 8-10 years. During this time, the kitchen will need to be renovated, rearranged in connection with the new interior, and a possible move.

The refrigerator may need to be moved to a new place and it is not a fact that a right-hand opening door will be convenient to use the refrigeration unit - the first option.

The second option is to open the freezer and cooling chambers in different directions. Here you also cannot do without re-hanging the doors.

Option three is damage to the doors, when they will need to be replaced or repaired, for which they will need to be removed without damaging the refrigerator body.

Atlant and Indesit: is there a difference in fastening

In terms of sales volume in Russia, the leaders are 2 brands of refrigerators that meet the desires of picky buyers - the Belarusian Atlant (formerly Minsk) and the Lipetsk Indesit (formerly Stinol).

The most popular of the Atlants are the narrow XM 4214-000; the easiest to maintain XM 4524-100 N and the super capacious MXM 1845-62.

From Indesit - roomy Indesit DF 5200; the trouble-free Indesit BIA 18 and the economy class Indesit SB 167.

Meeting the aspirations of the consumer, manufacturers Atlanta and Indesita have provided for the possibility of rehanging the doors on opposite sides if the original layout of the apartment has undergone changes.

Since the models of the considered brands do not have fundamental differences in the way the doors are fastened and the design solution for the absence of external handles is the same for them, knowing how to hang the door of an Indesit refrigerator, it is easy to carry out this procedure yourself and with an Atlant brand refrigeration appliance.

I recommend to read:

Source: https://holodilnik1.ru/instrukcii/kak-perevesit-dver-u-dvuhkamernyh-holodilnikov-indezit-i-atlant/

Changing the handle position

When the handle is part of the body, it will not need to be reinstalled. But how to hang the Indesit refrigerator door if the handle has 2 parts? To do this, you will need to reattach the harness leading to the display. There should be a hole at the top that will be considered a plug. It is necessary to disconnect the connector with the wires, stretch the harness, and secure it.

The handle is removed with a screwdriver, and for a new installation, plugged holes are needed. You just need to remove the handle and plugs and attach them in a new place. Old areas should be hidden with plugs.

How to remove the door

Before starting the procedure, empty all chambers of food so as not to interfere, turn off the device from the network and let it thaw.
This is necessary so that the rubber seal on the door straightens and takes its natural shape - when adjusting the door in a new position, this will play a big role. Indesit refrigerator doors are mounted on a rotating hinge with slight variations in the location of hardware for different models:

But how to hang the refrigerator door without damaging or breaking the appliance itself? To remove it, you will need a screwdriver or screwdriver. Decorative plugs are removed with a knife or a flat-head screwdriver, and the bolt heads must have slots for a Phillips screwdriver. If they are not there, select a wrench of the required size.

The first to remove is the false panel of the refrigerator compartment so that you can get to the wiring harness connecting the display on the door with the automation of the household appliance (if there is a display). After removing the false panel, loosen the harness so as not to break the wires when removing the door. You can completely disconnect the panel with the display (it must be connected using a connector) - this will make it much more convenient to work.

Then remove the handle (more on this below) and loosen the lower door fastening, then the upper one. After this, you can completely unscrew the lower canopy and, holding the door, release the lower hinge from the fastenings. The door is removed from the upper canopy by lifting it up. Now set the door aside and start looking for places to attach the hinges on the opposite side. Technological holes for new fastening must be closed with plastic decorative plugs or a decorative plate.

Some Indesit models require the use of additional parts when rearranging doors. The complete set of these parts is provided by the manufacturer - they must be in a package with instructions.

Recommendations for beginners

The instructions for completing the work will help you understand how to rehang the doors on the Indesit refrigerator. Tips will help you do this job efficiently:

many Indesit refrigerators are two-chamber, and therefore it is necessary to reinstall both doors, otherwise the operation of the equipment will become more complicated;
It’s better to start with the refrigeration section first, and then the freezer;
if the equipment does not have a lower hole, which is why you need to additionally purchase a left-sided lower loop, you can make the holes yourself;
If there is a display, installing the door becomes more difficult: you will need to remove the cable under the top hinge;
the procedure will not solve the problem of the door not fitting tightly, since this indicates damage to the seal;
To independently adjust the tightness of the door, you will need to tilt the refrigerator using adjusting supports;
after repair work, the equipment should not be turned on for about 8 hours, and then it is ready for operation;
if the refrigerator is under warranty, then you should not interfere with it yourself: such work can cause a complex breakdown;
If you have doubts about the correctness of the work, it is better to contact a professional.

If the old gum has dried out, then it needs to be replaced with a new one, and the problem will be eliminated. And then there is no need to overweight the door. It is enough to follow all the rules of the instructions, and the equipment will work for a very long time.

Common problems

The main defects of the refrigerator door are a loose fit to the body or, conversely, difficulty opening. In the first case, poor contact of the sealing element can cause compressor failure due to overload. In the second option, the main thing is the inconvenience of using the unit for its intended purpose.

Refrigerator door repair.

Watch this video on YouTube

Door opening is difficult

The defect of seal sticking is observed in the latest models of refrigerators during the first time after purchase. A vacuum is created inside the refrigerator, which suctions the door to the body of the refrigerator. This happens if the time interval between the first and second opening of the door does not exceed 3 minutes. Physical explanation of the problem: air at room temperature during the first opening enters the refrigerating chamber, where it is instantly cooled and compressed.

If you try to open it after a few seconds, the door will open with difficulty. Within a few minutes, the pressure in the refrigerator is equalized due to air leakage through the door seal. After several months of using the refrigerator, the rubber-magnetic gasket will lose its initial grip.

Sagging adjustment

A common cause of skewed refrigerator doors is excessive food load on its inside. Under their weight, the upper hinges come out of the grooves. Strong and frequent slamming when closing the refrigerator can damage the fastening of the door.

It is important to install the unit level. An uneven floor will cause the door to warp on its own over time, especially if the gasket is worn out and does not adhere well to the body of the refrigerator.

The reasons for the door coming off are determined using a quarter of a notebook sheet, which is placed on the seal and the refrigerator is closed:

The paper falls out without being held in the opening, which means the hinges are loose.
In some areas of the gasket the paper is retained, in others it falls out. The door does not close due to deformation of the rubber.
When the door closes, it receives a reverse impulse and moves away: failure of the spacer (plastic part at the bottom of the door on older models of refrigerators).

A door that is not closed tightly will allow warm air to pass through. As a result, the compressor will work without interruption to maintain the temperature at the proper level. In this mode it will quickly fail.

Creaking

The door of a new refrigerator may creak when opening until the hinges have been developed. A creaking sound may mean that the lubricant has dried out on the hinges and the metal parts are rubbing against each other.

Other Recommendations for Refrigerator Door Repair

Other problems, in addition to replacing the rubber seal, when minor DIY repairs of the refrigerator are required, are the door creaking or reinstalling it. You can eliminate the appearance of a squeak in the following way:

Identify the hinge (or several hinges) that squeaks when opening/closing the refrigerator door.
Eliminate the defect with a drop of machine oil by placing it in the door hinges (under no circumstances use vegetable oil, i.e. edible oil, for these purposes).

Thus, simply adjust the hinges by lifting them (as far as free movement allows) and dripping a few drops of oil onto the axle in order to get rid of the unpleasant creaking sound.

Another, no less difficult job of self-repairing a refrigerator is adjusting the door when it is reinstalled or sagging, which is done using plastic shims. Depending on the amount of door subsidence, you will need to purchase 2-4 such washers.

In order to adjust the refrigerator door with your own hands when it is sagging, you need to carefully remove the door by unscrewing the refrigerator panel and removing its fasteners at the top. Then you will need to place adjusting washers (1-2 pieces) on the bottom bracket pin and adjust the door horizontally. Next, all that remains is to “put” the refrigerator door in place, checking it for any distortions and cracks, as well as for the tight fit of the rubber band to the body (or door) and the operation of the light switch in the refrigerator.

Before you start repairing the refrigerator door yourself, it is strongly recommended not to load the refrigerator door with food from the inside.

If a break in the mounting hole is detected, the door will simply need to be moved to the opposite side, where it is intact. Similarly, adjust the door for distortions (see description above) using adjusting plastic washers. If the hole breaks in two places and it is impossible to hang the door, a plate will need to be strengthened onto the damaged surface using “cold welding.” Then prepare a hole of the appropriate size for the bracket axis and hook the door into its original place.

How to easily eliminate sagging Vestel refrigerator door

Watch this video on YouTube

How to hang a refrigerator door. With your own hands

Watch this video on YouTube

How to hang refrigerator doors yourself? Re-hanging doors with display!

Watch this video on YouTube

How to rehang doors on a refrigerator

Watch this video on YouTube

Features of outweighing from popular manufacturers

Refrigerator models from different manufacturers differ slightly in their design. Therefore, the procedure for rehanging doors on certain models of refrigerators from different manufacturers has some peculiarities.

How to remove the Atlant refrigerator door? To rehang the doors of a refrigerator manufactured under the Atlant brand, you must first remove all decorative elements and then dismantle (using a screwdriver or screwdriver) the fasteners.

Then, after carrying out the preparatory work, you need to carefully pull the bar towards you. This then opens up access to the foam, which serves as an insulating material. The foam must be removed from the installation site without damaging it or compromising the integrity of the structure.

After the foam has been removed, you need to use a hexagon to twist the top loop, while the middle loop is completely removed. Then you need to disconnect the door, lifting it up a little. The lower fasteners, after they are freed from the linings, must also be carefully twisted. After these steps are completed, the hinges are moved in a mirror position to the opposite side of the refrigerator and reinstalled.

How to hang the door of a Samsung refrigerator? Carrying out work related to rehanging the doors of refrigerators produced under the Samsung brand is carried out in a standard way. First you need to disconnect all the contacts that are located directly under the cover. Then you need to transfer the loops to the other side and reassemble the wires that are connected to the display.

Attachment points

How to rehang the doors on an Indesit refrigerator? Before you begin work related to moving the doors of Indesit brand refrigeration cabinets, you need to make sure that the design of the refrigerator allows you to manipulate their rearrangement. To perform a procedure such as rehanging the doors of an Indesit refrigerator, you must:

Inspect the household appliances and make sure that the doors can be moved (not all models have the appropriate connectors for hanging the facades).
Disconnect the device from the power source and remove all contents from it (food, storage shelves, etc.).
Dismantle the handles and also remove the plugs that are installed on the holes in which the doors are to be mounted.
Remove the upper and lower bolts.
Remove the door and the hinges.
Move the elements to the opposite part of the body.
Reassemble the elements in the reverse order, and then adjust the hinges.

How can you hang the door of a Bosh refrigerator? Reinstalling the doors of refrigerators manufactured under the Bosh brand is quite simple. To do this, you must follow all the recommendations, as well as adhere to the procedure specified in the technical documentation of this household appliance. To reinstall the doors, you need to remove special plugs from the fasteners, dismantle the fasteners, and then disconnect the handle, as well as special hinges. After this, all the elements must be transferred to the other side of the household appliance and assembled in the reverse order.

Minor difficulties may arise when moving doors that are equipped with a digital display. In this case, the procedure is as follows:

First, carefully disconnect all display cables;
then the door is removed, as well as the panel that masks the wires;
at the last stage of reinstallation, the loops are twisted, the contacts are transferred to the other side, and all the elements are assembled in the reverse order.

How to rehang the door on an LG refrigerator? The doors on refrigerators, which are produced by the LG brand, are secured using special hinges. To dismantle them, you must use a screwdriver or a simple screwdriver with the appropriate size. Before dismantling the doors, they should be securely attached to the body of the refrigeration unit using ordinary masking tape. Then the decorative elements and hinges are removed, after which they are mounted in a mirror order on the opposite side of the refrigerator. After installation, the hinges must be adjusted, loosening or, conversely, increasing their tension.

Preventing door sagging and crack formation

In order to avoid these problems in the future, you need to follow these simple tips:

the refrigerator must be level;
do not store too heavy things on the door;
periodically wash the gum from crumbs and debris using a disinfectant detergent;
Once a year, go over the seal with hot water or a hairdryer.

How to adjust the refrigerator door with your own hands? One of the most common local problems associated with a refrigerator is the deformation or lack of a tight fit of the seal to the door or body. In this regard, the question of door repair arises. Most often, you can do this yourself, because... Calling a technician to your home is not a cheap service.

Identifying and self-correcting seal faults

Local identification and correction of breakdowns associated with the refrigerator door, which can be easily eliminated yourself, can be identified in several ways. Firstly, during a visual inspection, when the refrigerator door does not adhere well and then opens easily or sag significantly, you will need to carefully remove the protective cover from the hinges (if there is one) and tighten the door to the required level. It is quite possible that the gap that appears is due to the sagging of the refrigerator door.

Secondly, if a loose fit is due to deformation of the rubber seal, because Since the material loses its elasticity over time, it can be returned to its previous state by heating. To do this, you will need to use a heating device (industrial or household hairdryer) or a thin stream of boiling water from a kettle to heat (pour) the deformed area of the seal, and while it is elastic, give it its original shape by placing a spacer (a piece of rubber, paper or dense foam) under the heated area. .

Attention! When fixing (heating) a deformed rubber seal on the refrigerator door with your own hands, you must follow the rules of personal protection, i.e. use gloves and place a rag on the floor to prevent hot water from flooding the room. In this case, the rag will need to be periodically squeezed out of excess water into a bucket, and then the waste water can be drained into the sewer. It is recommended to give the “elastic band” its original shape using gentle hand movements. When adjusting the seal, be careful not to burn your hands.

Thirdly, before adjusting the refrigerator door and trying to restore the damaged seal, you will need to pull out its edge with a thin screwdriver and consider the method of fastening. It can be on bolts, glue, special clamps or in slots (grooves). Replacing the seal on the body (or door) of the refrigerator in whole or in part is carried out by measuring the old element and gluing a new one in place to magnetic strips prepared in advance, which are inserted into the cavity of the gasket profile. If you don’t have a native seal, you can try to order and buy a universal one. Such repairs to a worn or damaged rubber seal are most often carried out only if it is installed on an Atlant, Minsk or Oka refrigerator.

Re-hang refrigerator doors

Watch this video on YouTube

Sources

https://InvestGazeta.ru/dlya-kuhni/kak-snyat-dver-holodilnika-indezit.html
https://vybordveri.ru/info/indesit-kak-perevesit-dver-holodilnika/
https://okna-dveri73.ru/remont/kak-perevesit-dver-holodilnika-indezit.html
https://dibroff.ru/gadzhety/kak-perestavit-dver-holodilnika-na-druguu-storonu.html
https://fotografnn.ru/dveri/kak-pomenyat-mestami-dver-na-holodilnike-indezit.html
https://ozrbu.ru/kak-perestavit-dver-na-holodilnike-indezit/
https://in-teck.ru/byt-i-zdorove/pereveshivanie-dverej-holodilnika-atlant.html

Do you want to understand better than others?

How to move the refrigerator door to the other side yourself: detailed step-by-step instructions - The easiest way to do this is when such manipulations are provided for by the design of the unit. In this case, technological holes are made on the door on both sides. Only…
How to hang the door of two-chamber refrigerators "Indesit" and "Atlant" - Choosing a refrigerator for a modern kitchen is a responsible matter. It is necessary to provide for a lot of seemingly insignificant little things that can subsequently affect the convenience...
Video: how to rehang the door of an LG refrigerator with a display - Video: rehanging the door of an LG refrigerator with a display

Video: how to rehang the door of the LG GA B499SMQZ refrigerator

Video:…
How to hang the door of an LG refrigerator without a display? — Why do you need to replace doors? The activity of the right or left hand is a sufficient reason for reinstallation. The door leaf of a refrigerator, especially a large one,…
How to rehang the door in a two-chamber refrigerator Biryusa - Re-hanging: is it possible or not? Many people are interested in the answer to the question of how to rearrange the door on the refrigerator. But there are also some nuances here. Many refrigeration manufacturers...