A bra wire got into the washing machine - what to do and how to get it out

When washing different clothes in a machine, the user unintentionally clogs the machine with various small parts. These could be handkerchiefs, underwires from bras, socks, buttons, coins. Moreover, these objects get stuck in the most incredible way. Socks and handkerchiefs can wrap around the drum shaft, buttons, buttons and bones from women's clothing can get stuck between the walls of the device and the drum. How to remove foreign objects from the machine without damaging the equipment? Professionals involved in repairing washing equipment will tell you about the secrets of removing small parts and things.

How to remove a foreign object?

Frame wire for a bra: what is it made of and what harm does it cause?

At first glance, if you compare the size of the machine and the linen accessories, it seems that it is unlikely to do any harm. But the point is not in size, but in the material from which the bone is made.

Most often, frames or bones for linen are made of metal or coated steel.

Getting stuck in the tank of the machine, such corsetry parts begin to rust, stain water and washable items, and can tear linen. And these are even the easiest of troubles. Much worse is that a sharp metal bone can easily pierce the washing machine tank, damage the coating of the heating element, tear the cuff or drain pipe.

If the fittings are made of plastic, then they are less destructive.

Although, when a plastic bone has fallen deep into the washing machine, it can also make a mess. For example, pierce the same drain pipe or slip into the pump and disable it.

Where to look for a bra wire

An uninvited guest gets into the washing machine, falls through and gets stuck in different places:

  • in the perforation of the drum;
  • at the bottom of the tank (the most common case): under the heating element or between the bends of the heater tube;
  • in the space between the drum and the tank (top, side, back);
  • in the drain pipe, filter or pump (very rarely).

Depending on the place where the bra wire is, you can get it out in five ways.

Attention! Before you start disassembling the washing machine, unplug it from the power supply! Follow safety precautions, this will protect you from injury and electric shock.

Prevention

To protect your equipment from damage and not disassemble it in order to remove a bra bone that has fallen into the tank, you need to follow several recommendations.

  • Clothes with rhinestones, plastic or metal parts, including bras with underwires, should only be placed in the washing machine in a washing bag.
  • Small things - belts, handkerchiefs, socks - should also be put in such a bag.
  • Before storing things, carefully check your pockets.
  • Monitor the condition of the rubber seal near the hatch.
  • Before each wash, check that there are no foreign objects in the drum.

By following these tips, you can not only get the “extra element” yourself, but also avoid unnecessary hassle associated with disassembling the washing machine or even repairing it.

“>

The first method is how to remove a bone from a washing machine through the drum

Can be used if the bone has just begun to fall through and sticks out with the tip outward from the perforation of the drum.

To locate the part, examine the drum from the inside over the entire surface with your hand. It is very difficult to see thin fittings in shiny metal, but they can be easily identified by touch.

Hook the tip of the bone with tweezers, narrow-nose pliers or wire and pull it out.

The second method is to remove the bone through the heating element

Attention! This method is suitable for horizontal washing machines with a rear heating element, when the heat element is located under the tank at the bottom.

You felt the drum and found nothing sticking out. This means that the accessories that “escaped” from the laundry have already slipped into the tank. From repair experience, craftsmen know that when a bone from a bra falls into the washing machine, most often it falls to the bottom of the tank and gets stuck in the TEN area. And you can get it out by removing the heating element from the washing machine tank. In fact, you need to remove the heating element, find and pull out the bone, and then put the heater in place.

For this:

  • Remove the back cover from the machine.
  • Turn off the power to the heating element, remove the terminals from the contacts. Typically, three wires are suitable for the heater: phase, neutral and ground. Phase and neutral have a terminal contact; the grounding contact can be secured with a nut on the central stud.
  • Loosen the fastening nut on the stud. You will see it when you remove the grounding. Unscrew the nut until it is flush with the end of the stud (there is no need to remove it at all).
  • Carefully press the pin inside the heating element so that it “sinks” up to the nut.
  • Move the heating element and remove it from the socket (sometimes serious effort is required).

Attention! Do not swing the heating element by its contacts or pry it with a screwdriver. You will damage the contact pins or sealing collar.

In half of the cases, the bone is removed along with the heating element because it gets stuck in the loop of the heater tube. In other cases, it is found at the bottom of the tank under the installation site. Often, instead of one fitting, there are two, or even three.

Housewives do not always associate the loss of a frame from a cup with the washing machine, and a bone can slip into the tank without noise or knocking, without showing signs of its presence. Therefore, it is located only when disassembling the heater, behind.

Inspect the TEN carefully for damage. Sometimes a metal strip breaks the heater very badly, literally into pieces.

But more often it leaves small dents or scratches on the tube, which are hardly noticeable. And the owners of the machine put the damaged element in the tank, and then are forced to carry out serious repairs to the equipment due to a breakdown of the heater, electrical short circuit and other surprises. Therefore, it is safer to immediately change even a slightly dented heating element.

When the bone is pulled out and the heater is normal, you can put it back in place.

The procedure will be the reverse of disassembly:

  • Push the center pin outward by pressing on the inner mounting plate.
  • Insert the heating element into the hole, gently pressing the cuff.
  • Screw the fastening nut onto the stud. Do not tighten it all the way, you will compress the seal and it will leak water from the tank. It is better to tighten it a little looser and then tighten it if necessary if moisture appears in the hole. But, as a rule, the seal seals the tank well and additional tightening of the nut is not necessary.
  • Connect the power supply to the TEN.
  • Plug in the machine and run a test wash without replacing the back cover. To check if there is a leak from the tank through the heater socket.

Attention! Be careful not to touch the inside of the machine with the lid removed while washing.

If everything is in order, there are no leaks, secure the lid, having first disconnected the washing machine from the mains.

What to do if the bra bone is not visible through the hole from the heating element?

If an object is stuck between the tub and the washer drum near the shaft at the top of the tub, it may not be visible through the heating element hole. In this case, you need to perform a number of actions.

  • Block the pulley with a wooden block. This is done so that the drum does not rotate during further actions.
  • Unscrew the pulley mounting bolt.
  • Remove the pulley and screw the bolt back (do not tighten it all the way).
  • Perform several sharp blows with a hammer on the bolt. In order not to damage the thread, blows must be applied by first placing a wooden plank.
  • After the impacts, the shaft with the drum should move forward, and the foreign object should fall down.
  • Put the pulley in place, tightening the bolt tightly so that it cannot come loose during washing or spinning.
  • Replace the back wall and cover and tighten all fasteners.

The third method is how to get the bone through the drain pipe

This method can be used if you do not want to remove the heating element or when it is located under the front cover, for example, in Samsung machines. Disassembling such a model causes difficulties for equipment owners - they need to remove the cover, cuff, front panel, etc. to get to the heater. Therefore, it is easier to remove the mounting clamp and look into the tank through the pipe.

The procedure for washing machines without protecting the housing from leaks will be as follows:

  • Place the washing machine on its side.
  • We remove the bottom, if there is one: unscrew the fasteners or snap off the latches.
  • Loosen the fastening elements on the pipe (clamp or ring) and remove it from the ledge of the tank.
  • We inspect the drain hole and the visible part of the heating element and tank. We take out the bone from the bra. Sometimes it falls out of the pipe on its own, but more often you need to look for the fittings by shining a light into the hole.

After removing the foreign object from the tank, we install the pipe in place, fix it with a clamp, secure the bottom, and turn the machine over to its normal position.

If you are the happy owner of a washing machine with the Aquastop system for protecting the body from leaks, then we recommend getting to the drain pipe through the back wall. In this case, of course, you won’t be able to look into the hole in the tank onto which the pipe is placed; you’ll have to go by touch, but removing the bottom where the Aquastop is installed is still a task, even for a master. After all, you first need to dismantle the leakage protection system, and for this you will need to disassemble half the machine.

The described method can help remove a bra wire from a washing machine with a front-mounted heating element without much disassembly, but it does not always work. The drain hole where the pipe is attached is quite narrow. If the bone does not lie directly above it, but far to the side, higher or lower, it is difficult to see it and, even more so, to pick it up. In addition, if removing the bottom of the machine is problematic (for SMA with protection of the body from leaks), then the possibilities of the search operation are reduced even more: it is inconvenient to crawl up to the tank from below, you have to search for a bone by touch, as far as your fingers can reach, etc.

How to remove a foreign object with your own hands?

As mentioned above, there are two extraction options:

  • The movement of the item is against the movement of the drum. It is necessary to rotate the drum with your hands until the object can be removed - it is necessary to “rewind” everything back and safely remove the “clogging”. Also, on some models there may be installed automatic protection against such “extraordinary stops”, which will immediately stop the washing cycle at the first overload in the engine operation - if such protection is not installed (found on budget models and Soviet-made samples), it is recommended install it as an add-on.

It is important to note! Some washing machines have a built-in drum “reverse rotation” function, which allows you to manually rewind the moving part of the element to the moment the item was “placed”. This helps you remove items safely, with minimal potential damage to your appliance and clothing.

  • Removing things from outside the drum. If the item is already outside the drum, it is necessary to remove it and disassemble the washing section. You can do this yourself or involve a specialized specialist in the work. In both cases, the machine must be disconnected from the power supply and all water drained. Next, following the factory recommendations and instructions for disassembling the “working compartment”, you need to open access to it. After this, it will be possible to remove the object - by pulling it along the movement or, conversely, to help it come out using a countercurrent.

You can use additional tools, such as a screwdriver or long metal pins, to help you remove things more efficiently. Try to use your fingers less - they can easily be damaged when working with rotating elements of mechanisms.

If the situation is critical and cure is impossible, mechanical cutting of the thing is necessary - you can use ordinary scissors or wire cutters, followed by removing all remnants of the “work”.

Of course, if possible, you should refuse to wash such things in the future that end up in the elements of the washing machine - use hand washing or another washing machine for them.

Fifth method - remove the bone from the drainage system

It happens that the bone safely slips through the tank with the heating element and ends up in the drain system of the machine - in the pipe, filter and even the pump. We are mainly talking about plastic accessories for ladies' corsetry. It, unlike metal, is not so rigid and easily breaks in the drum, without causing significant damage to the parts of the washing machine. That’s why it “flies” so far.

Bone in the filter

First, check the filter. It is usually located in the lower left corner of the front of the car behind a special hatch.

To clean the filter and possibly remove the seed:

  • Open the hatch. It is fixed with a latch, so you need to press the cover or carefully pry it off with a screwdriver.
  • Slide a dry cloth under the washing machine in the area of ​​the filter or tilt the SMA back, resting it on the wall, and place a container so that the remaining water does not spill onto the floor.
  • Unscrew the filter and pull it out of the hole.
  • Inspect the filter and the hole, the bone may be there or there. At the same time, remove any other small debris that has gotten into the car. Wipe the filter installation hole and rinse it with running water.

If the bone is found, then everything is in order. If not, look directly into the pump (in the case when it is located directly behind the filter in front). You may see a piece of plastic sticking out and you will be able to remove it.

Bone in the pipe

If nothing sticks out of the pump and the machine drains water normally, then most likely a bone is stuck in the pipe. There is a third way to get it from there.

But first you need to put the filter in place and close the hatch. Tighten the filter carefully and at the same time tightly so that the machine does not leak during washing.

Bone in the pump

The first sign that an “uninvited guest” is in the pump is that the machine either does not pump water out of the tank or does not drain well. The pump may make a lot of noise and grinding noise. This is not good, but if the pump crackles and goes completely silent, it’s even worse. Silence indicates that the engine has burned out and the pump will have to be replaced. Therefore, try to deal with the situation while the pump is still alive and making a lot of noise.

To remove a foreign object you need to get to the pump and open it.

In different brands of washing machines, the pump is located differently. And you need to get to it in different ways.

  • In most cars of the brands Ariston, Ardo, Veko, Indesit, Samsung, Candy, Whirpool, LG, the pump is located below the filter. Therefore, you can first inspect the pump through it. For full access, it is most convenient to place the machine on its side and carry out all operations through the bottom.
  • In the Electrolux and Zanussi brands, the way to the pump is through removing the back panel, because the pump is located closer to it.

  • The “Germans” (AEG, Bosch, Siemens) have the most difficult path. You need to remove the top cover and front panel, as well as pull out the dispenser, remove the locking of the hatch cuff and disable the door lock.

Attention! We recommend contacting specialists immediately if you have German equipment. Since disassembly and assembly in these brands is complex and requires experience and accuracy. You can damage the car if you do it yourself

Pump disassembly

The design of the pumps is practically the same. To inspect the “insides” you need:

  • Prepare a container for water or a rag. When you disconnect the pump, water will flow out of it. To prevent a puddle from ending up on the floor, perform disassembly operations over a basin or place a rag.
  • Disconnect the pump from power. To do this you will need to disconnect the connector.
  • Remove the screws that secure the pump to the housing.
  • Disconnect the drain hose on one side and the pipe on the other by loosening the clamps.
  • Disassemble the pump. To do this, you need to unscrew the volute from the body and pull out the engine and impeller from it.

Now inspect the pump from the inside. The bone may be located between the impeller blades or pressed against the casing. Pull it out and inspect the impeller itself for damage. If there are any, then you will have to change the pump (impellers are not sold separately). Even with a “live” engine, a pump with a broken impeller will not drain water.

It is rare, but it happens that the bone did not have time to disable the pump, but simply slowed down its rotation. Then you are in luck and after removing the “alien” you can assemble the pump and put it in place.

Check the pump for leaks before assembling the machine completely, plug it in and put it on a quick wash.

Be careful! Do not touch the internal parts of a working washing machine that is not fully assembled.

Features of troubleshooting: why did a foreign object get into the drum?

The first, and most obvious, reason is the design features of the drum.

Designers are trying to combine several main functions and tasks in this element: savings in production, washing efficiency, optimization of noise emissions, and others. Due to the multi-faceted nature of the task, it is impossible to calculate all the types of fabrics and shapes of clothing that will be used, which could mean an item entering the drum and stopping the entire wash cycle.

If this happens, it is recommended that the first thing you do is simply try to pull out the foreign object in the countercurrent movement of the drum, which in most cases will be successful - the object will be removed.

The main feature is that a foreign object can be removed by a “countercurrent” movement against the drum, or the object has already penetrated outside the drum and then outside help is needed. The second option is more complex and will require a more complex algorithm of actions from you.

The wire from the bra fell into the washing machine and lies quietly - take it out or leave it there

Sometimes a bone clearly disappeared in the car, the owner pulled out her bra and noticed. But at the same time, the washing machine does not make noise, does not tear things and works like a clock. What to do in this case, should you search and pull it out or leave the “alien” inside?

Theoretically, you can leave it, but craftsmen find deposits of bones in machines when disassembling them due to other faults. But remember that even the fittings lying quietly in the tank are a foreign object that should not be there.

A metal or plastic bone at the bottom will eventually become covered with dirt (hair, dust from clothes, threads), which will smell unpleasant and you will have to think about how to remove the musty smell from the washing machine.

In addition, metal lying in a damp place and constantly getting wet during washing/rinsing will begin to rust and stain the water in the tank, which will contaminate things. Removing rust stains from laundry is very difficult, and sometimes even impossible. That is, the damaged item will have to be thrown away.

A plastic bone is also dangerous because when it comes into contact with a heating element, it begins to melt when heated and smells like burning. This can ultimately lead to damage to the heat element.

Masters recommend! If a bone is stuck in the washing machine, remove it as quickly as possible. For example, after 1-2 washes. Otherwise, big problems may await you due to the extra detail.

How to avoid problems?

To prevent breakdowns and not resort to expensive repairs, it will be useful to listen to constructive recommendations:

  • Make it a rule: before washing, you should turn out all the pockets of your clothes.
  • Sew on poorly holding buttons and small accessories in a timely manner.
  • Look inside the machine and into the powder drawer before loading clothes.
  • Buy laundry bags. They come in a variety of shapes and sizes, and can be used to wash everything from socks to down jackets. There are even special containers for washing bras. You can also wash sneakers and textile shoes in bags. Thanks to such useful, unpretentious devices, you will maintain the attractiveness of things and protect your washing machine from troubles.

Video “How to remove a foreign object”:

What is the danger of getting a bone into the drum?

Smell, dirt, rust on clothes, torn items are minor troubles compared to what a bra wire that has fallen inside the washing machine can do.

We already talked about serious problems when we figured out what kind of object this is - a bra wire. Now let's take a closer look at them.

Linen accessories in the washing machine:

  • Deforms the drum and damages (pierces) the tank. A sharp metal plate ruptures the drum cells or flies into the tank wall like a bullet, making a hole. As a result, you have to change the tank or even buy a new washing machine.
  • Destroys the heating element or damages its surface , which leads to breakdown of the heating element. When a metal bone gets stuck at one end in the perforation and the other ends on the heating element, it cuts the heater tube like a knife. If the fittings fall inside the loop, it breaks the heat element into pieces. As a result, you have to change the heating element.
  • It tears the tank cuff and causes a leak. As a result, you need to seal the original cuff or replace it with a new one.
  • Pierces the drain pipe . If a bone gets into the drain hole, it can pierce the rubber pipe with its sharp end. Repairing holes in it is difficult and unreliable, so it cannot and must be replaced.
  • Damages or disables the pump. Most often, plastic bones slip into the pump; they break into pieces quite easily when they get into the drum. Once in the pump, bone fragments can damage or jam the pump blades. In the case of a “wedge”, the pump will hum strainedly, but will not pump water. If the obstacle is not removed in time, the engine of the unit will burn out and you will have to install a new pump.

How did the object get into the car?

First of all, we need to say why foreign objects appear in the washing machine. They end up in the car along with the clothes whose pockets you were too lazy to check. The most common item is money, or rather coins, although paper coins also sometimes end up in the drum. In addition, some managed to wash a credit card, passport, phone, gold chain and rings. Often, service center technicians take seeds, pins, bolts, nuts, and hairpins out of the car.

What to do if another foreign object gets into the washing machine

The bra pit in the washing machine is not the only “uninvited guest.” During inspections, craftsmen find coins (even anniversary coins!), buttons, pins, curtain fittings, Lego parts, bolts, screws, nails and other small items. The dimensions of this “good” are smaller than those of a stone and they are less likely to linger in the perforations of the drum or at the bottom of the tank.

Their favorite habitats are:

  • Cuff near the door hatch. “Creeping small fry” easily gets into the fold and remains there.
  • Drain pipe. There are small metal parts, screws, and nails left in it.
  • Drain filter. There may be a warehouse of coins, nuts and screws, and small plastic items. Everything that slipped through the pipe, but did not have time or could not fly into the pump.
  • Water pump. It carries light plastic parts, such as parts of a children's construction set, matches, small fittings, and buttons.
  • Drain hose. Matches, small pins, and plastic dowels fly through the pump.

Since the size of this “good” is small, they usually do not cause significant harm, such as breaking the heating element or damaging the tank. But, for example, a nail or self-tapping screw is quite capable of damaging the heating tube, unraveling the perforation of the drum, or even making a hole in the tank. And it’s easy to break the pump or cause a blockage.

Therefore, if there is extraneous noise in the machine, pump noise or other strange sounds, it is worth looking to see if there are any foreign “guests” in the inside of the washing machine. If it’s difficult to handle on your own, call a repair specialist.

When to call a specialist?

Three situations are possible:

  • A thin object, such as a bra wire, got stuck in one of the holes in the drum. To remove it, pinch the accessible end with pliers and gently pull, being careful not to break it. Of course, such a task can be completed without a specialist.
  • The loss is not visible, but you are sure it is in the typewriter. Small things like a chain, screw, or coin may end up in the drain filter. It’s not difficult to get them yourself - you don’t need a master either.
  • If you hear a clanging noise as the machine is running, as if metal is rubbing against metal, a foreign object may have gotten underneath the drum. At this point you need to call a specialist. A metallic sound may also indicate wear or malfunction of a part. It is difficult to diagnose a breakdown without the help of a specialist.

Rating
( 2 ratings, average 4.5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]