Reasons why the Indesit washing machine does not turn on

Electrical faults

In some cases, the Indesit washing machine is fine. The reason is a network fault. The repair consists of checking the outlet. To do this, simply plug a known-good device into it.

Sometimes the washing machine does not turn on or work due to a faulty cable. In both cases, you must be careful: turn off the electricity and only then begin repairs. It is advisable to entrust this matter to a professional electrician.

Socket repair

Do-it-yourself Indesit washing machine repair

The malfunctions specific to machines of this brand were described above. But they are not insured against the usual breakdowns typical of all washing machines. Here are the most typical ones:

Waste water is not poured out

The simplest reason is a clogged drain system. To resume operation of the unit, it is enough to remove the accumulated dirt.

It is worse if the pump that pumps out the water fails.

This can happen due to overheating of its motor or a short circuit in the winding. In such cases, a new motor is usually installed.

But the reason may be simpler: sometimes the snail-shaped plastic pump body becomes deformed from prolonged contact with hot water, thereby pinching the impeller blades. It is advisable to replace the damaged pump housing with a new one. If it is not possible to do this yet, you can trim the impeller blades with a sharp knife.

To dismantle the pump, you need to remove the back wall of the machine. The node is located in its lower part.

The mode switch began to turn freely

You can try to “cure” this malfunction by purging the sensor. If this does not help, the device will have to be replaced.

The lock on the sunroof has stopped working properly

Such an incident is unpleasant in itself, in addition, it can cause the machine to simply refuse to turn on. The fact is that the lock also has contacts, and if something prevents it from closing completely, they remain open and power is not supplied to the unit components.

Locking the hatch of the Indesit Ariston washing machine

In most cases, the cause of lock failure is dirt accumulated in it. After its removal, the operation of the device will most likely be resumed.

The belt that transmits rotation from the engine to the drum is loose

First of all, you need to try to tighten the belt after disassembling the machine. Some models provide this feature. If the belt is very worn, it needs to be replaced.

Water does not flow into the machine

First of all, you need to open the tap on any mixer and make sure there is pressure in the water supply network.

If it is sufficient, you need to inspect the hose for pinching or depressurization.

If everything is in order with the hose, the problem may be a clogged coarse filter, which in this case is thoroughly washed.

A more serious reason for blocking the water supply is a failure of the level switch. This item can only be repaired by a qualified technician.

Bathrooms are most often not very spacious, so residents try to organize the available space as ergonomically as possible. The space under the sink is ideal for installing a washing machine. Choosing a compact washing machine under the sink - an overview of the main points.

How to choose a circulation pump for heating and what you need to pay attention to when purchasing, read this material.

Interference filter and network cable

The Indesit WISLI washing machine still won't turn on? Next you should look at the power cord of the Indesit washing machine and the plug, as well as the interference filter.

You will have to remove the network connector and the filter at the same time, since they are connected.

To do this you need:

1. Disconnect everything unnecessary from communications.
2. Turn the Indesit washing machine.
3. Remove the screws and then the cover.
4. At the top left is the capacitor. It needs to be removed from the mount.
5. At the base of the case there is also a mount that secures the cable. It needs to be disconnected.
6. After the previous manipulations, the network connector with the filter can be easily pulled out.

Interference filter in a washing machine

Next, you should disconnect the filter and check the power cord. This is done by ringing with a multimeter. If a breakdown is found, the entire wire must be replaced. It is not recommended to repair the old one or replace the cores in it.

Interference filter

After this, the interference filter rings. The probes are installed on the legs of its capacitor. If everything is normal, the resistance is additionally checked. If the value is “0” or “1”, the cause is the capacitor and must be replaced.

Repair of Indesit Wisn 101

This model has many advantages. However, users note a weak harness that is installed on the drum. If for this reason the Indesit Wisn 101 washing machine does not turn on, the display shows A6. To repair the model yourself, you will have to prepare the necessary tools. First of all, it is recommended to choose a set of screwdrivers. You also need a large wrench for the rod head. To begin the repair, remove the cover of the washing machine, which is located on the rear panel. The next step is to disconnect the rotor box.

Control module

If after this the indicators do not light up, then the reason is different. Next you should try checking the control module of the Indesit WISLI washing machine. These are microcircuits, the “brains” of the device. You need to change something here only with some experience behind you. A video will help with this work.

Washing machine control module

By the way, the causes of other common Indesit malfunctions also lie in the control boards:

• if all the lights on the panel blink;
• if there are problems with spinning, etc.

When the capacitors on the microcircuit fail, the indicators usually begin to blink simultaneously. Replacing capacitors is the easiest way, but you will need good soldering iron skills and the right model. After replacement, as a rule, the light bulbs stop blinking.

If there are problems with spinning, they also look at the electronic module. This is not an easy task and requires knowledge and preparation. That is why, if the spin cycle does not work correctly, it is advisable to give the board to a specialist.

Device is not working? Why does the Indesit washing machine blink and not turn on? You need to look at the varistor - part of the microcircuit, a resistor necessary to protect the board from voltage surges.

Varistors microcircuits

Replacing it is quite simple with your own hands:

1. Remove the powder container. Underneath there are two screws that need to be unscrewed.
2. Remove the control panel.
3. Disassemble the unit and disconnect the board.
4. Find the varistors and check their resistance using a multimeter. Often the part turns black or falls out completely.
5. The burnt varistor is soldered off. It is replaced by another one with similar characteristics. The device should start working.

When using a soldering iron, you need to be careful not to damage the traces and other elements of the printed circuit board. If this happens, most likely, you will no longer be able to do without the help of a specialist.

You should also keep in mind:

1. Varistors are not the only possible malfunction that leads to the Indesit WISLI washing machine not turning on. This is just one of the simple and common ones.
2. In case of inept repair, the microcircuit can be permanently damaged beyond repair. Its cost is approximately 20% of the price of the entire Indesit washing machine.
3. Service centers usually do not repair the board, but install a new one. It’s easier, faster, and most importantly – more profitable. Private craftsmen often undertake repairs. Their repairs will be cheaper, but you should pay attention to their experience and qualifications.

Prevention of breakdowns

Whatever equipment you have in your home, even if it is a well-known one, it requires appropriate care and prevention. If you monitor the condition of your home assistant, you can extend the life of her work for a period longer than stated in their technical manual.

There are quite simple rules that must be followed, which will help to avoid errors in operation.

• When washing bras and lace underwear, it is best to place them in special bags in advance. By following this rule, it is easy to avoid damage to the underwear - the lace will not tear and the bra wires will not fall out;
• If the door to the washing machine does not close securely, this can seriously affect the operation of the machine. Clothes stuck in the door will easily tear the rubber seal, which will subsequently cause water to leak out of the door cracks. Also, such inattention can lead to the drive belt breaking and even removing the controls. And this will have a catastrophic effect on the performance of the device in the future;

If necessary, you can always use the emergency water drain

• It is better to remove the plug from the socket after completing the washing process. Our electrical network is very often subject to power surges and such a necessary and very expensive device can easily fail. For insurance, you can buy a device to protect against voltage surges in the network and connect it to it;
• to avoid mismatch of phase wires, it is better not to use various types of extension cords;
• Many owners install the Indesit device in the bathroom. But we all know that this is where the humidity is highest, which cannot but negatively affect the operation of modern electronics. In addition, metal parts will most quickly be subject to corrosion;
• wash clothes in parts, do not load them in excess. High-quality washing cannot be achieved in this way, but it can cause increased vibration;
• metal fasteners and buttons must be fastened;
• if there are mice and rats in the house, it is better to get rid of such a neighborhood - they can seriously damage home appliances;

Do not forget to periodically clean the pump from dirt and foreign objects that have gotten into it.

• It would be useful to remind you that for washing it is better to use washing powders specifically designed for automatic washing. Excessive foaming can lead to breakdowns;
• Some people believe that the Indesit washing machine can wash everything. Feather pillows, shoes, and car accessories are not intended for machine washing - the shoes will get damaged, and feathers from pillows can clog the entire drain system of the machine.

Start button

Another reason may be that the device's start button is faulty. As a result, it does not turn on. Often such a breakdown occurs in older models of the Indesit washing machine, released about 15 years ago. Due to their features, if the button fails, everything else does not work.

The following actions are performed:

• the control module is removed according to the scheme discussed above;
• the resistance on the button is determined, and it must be on;
• If this is the case, a new one is installed.

If after all the above checks the machine still does not turn on, the reason is not common or something was done incorrectly. Then it is better to call a specialist.

If there is no power

There are a number of reasons why the equipment does not work after switching on. If the display or indicators on the Indesit washing machine do not light up, this indicates a lack of power. This happens if:

• There is no electricity.
• The machine or RCD tripped.
• The socket is faulty.
• The power cord is broken.
• The power button is broken.
• FPS malfunction.
• The control unit is broken.

Electricity problems

The first thing you should check if the automatic washing machine shows no signs of life is the presence of voltage. You can turn on the lights and other mains-powered devices to make sure there is electricity.

If there is a separate line to the Indesit washing machine, you should make sure that the machine is not knocked out. This could happen if moisture got into the outlet or there was a short circuit. You need to check it and turn it on if it is knocked out. If it turns off again, you need to look for the cause of the short circuit.

If the equipment is connected through an RCD, it could be triggered if electricity leaks to the body. Sometimes the protective confinement device fails if it is of poor quality or the wiring is poorly done.

Another reason why the Indesit washing machine does not receive power is a malfunction of the socket or extension cord through which the product is connected to the network. You can connect another electrical device to them or use an indicator screwdriver, a multimeter or a light bulb with wires attached.

Causes of level sensor failures

Sometimes the level sensors on washing machines break down. These elements fail due to malfunctions of the module. The breakdown may also be caused by network overload. Level sensors cannot be repaired, but they can be replaced. For this purpose, it is necessary to ensure that the elements are broken. To do this, remove the lid from the washing machine and inspect the drum. The level sensors are located under the plate and are connected to it through contacts. If the tester shows a zero value, then the device is broken. It needs to be changed.