Why the washing machine does not drain water: what to do urgently

Instructions for using the washing machine Ariston margherita 2000

Download (PDF, 1.49MB)

We have also made a link for you where you can download this manual for a front-facing washing machine to your computer for free.

If you follow the recommendations from this article on using a washing machine, you will certainly increase its service life, and also enjoy washing and using this home assistant!

Video review and repair of the Ariston margherita 2000 washing machine module

TOP stores of washing machines and household appliances:

mvideo.ru / - household appliances store, large catalog of washing machines
holodilnik.ru – Inexpensive store of household appliances.
techport.ru – profitable modern online store of household appliances
citilink.ru is a modern online store of household appliances and electronics, cheaper than offline stores!
ru.aliexpress.com – spare parts for washing machines

( 2 ratings, average 5 out of 5 )

Installation

Before you start using the washing machine, you need to take care of its installation. After the unit has been unpacked, it must be carefully inspected for possible damage. Don't be so sure that everything is fine with the machine. If you find something, call the store immediately, and don’t even think about turning on the machine.

If everything is in order, then you need to remove the shipping bolts that held the moving parts. They must be preserved; they may be needed, for example, when moving. The holes for the bolts can be closed with special plugs.

The next stage is leveling the surface on which the machine will stand. Usually the position of the machine itself is leveled by rotating the front legs, but this may not be enough. Read more about how to level the machine in the article on our website.

Having prepared the installation site, proceed to connecting the hoses. Using your hands, screw the inlet hose onto the ¾ diameter water pipe or its outlet. Then screw the bent end of the hose to the tube coming out of the back of the machine, coming from the fill valve.

Important! Be careful not to lose the rubber seal that is located just after the fitting washer.

Connect the drain hose to the sewer or outlet in the sink siphon, but only so that its end is not in the water. The upper drain point should be fixed at a height of 60-100 cm using a clamp on the back wall of the machine. When connecting, it may be necessary to increase the length of the hose; this can be done, but the total length should not exceed 150 cm.

Now all that remains is to connect the machine to electricity, but before doing this:

check that the wiring matches the maximum load of the machine;
whether the voltage in the network corresponds to the permissible standard;
whether the plug from the machine cord fits your socket, otherwise change the socket, but do not use an adapter;
Is there any grounding in the electrical network?

Powder cuvette

In the Ariston Margarita 2000 washing machine, the powder cuvette has a semicircular shape and opens outward. The cuvette is divided into 4 compartments. The leftmost compartment is designed for various fabric softeners and fabric softeners. The elongated compartment on the right is the main one; liquid or bulk detergent is placed in it.

The compartment located in the center is intended for pre-washing. You can put either liquid or dry laundry detergent in it. As for the fourth compartment, it is inserted into the pre-wash compartment in case you need to add bleach. At the same time, be careful and do not pour too much product, there is a special mark for this.

For your information! Prewash and bleaching are mutually exclusive and cannot be used at the same time.

Common breakdowns

All possible malfunctions of the washing machine can be divided into several groups:

Doesn't turn on.
Doesn't drain water.
There is no spin.
Does not open.
No heating.
Leaking.
Doesn't take up water.
Makes extraneous noise.

There may be several reasons for each of the listed malfunctions. For example, the lack of water in the tank can be due to either a broken inlet valve or a simple clog in the inlet hose.

Before you start repairing the Hotpoint-Ariston washing machine yourself, you need to determine the probable causes of the problems and possible methods for eliminating them.

Doesn't turn on

Possible reasons why the washing machine does not work when turned on:

the socket or power cord is faulty;
The control module is damaged.

It’s easy to check the serviceability of the outlet - just plug in another, working device. Damage to the cord can often be seen visually, by testing the cable with a multimeter to be sure. If there is no resistance between the “start” and “end”, the cord should be replaced with a new one.

Only a specialist can troubleshoot the Ariston Hotpoint module. The cause of failure may be a sharp surge in voltage in the network. Reflashing or replacing a module is an expensive procedure.

In some cases, after being plugged in, the machine signals that it is ready to work (the indicators light up), but after selecting a program, the washing does not start. There may be several reasons for this:

The inlet hose is clogged or the valve is faulty. The appliance cannot start due to lack of water.
The electric motor burned out. Most likely, in this case, the machine will fill with water, but the washing process will not advance further. As a rule, a breakdown is accompanied by extraneous noise.

Removing a blockage at the inlet is quite simple. To do this, you need to remove the inlet hose, wash it under pressure, and clean the inlet filter mesh with a brush.

Replacing a faulty valve proceeds according to the following scheme:

The inlet hose is unscrewed.
The top cover is removed (the 2 bolts on the back wall that hold it are unscrewed).
The clamps connecting the pipes and the valve are unfastened, and the terminals are removed.
The valve is pulled out from its seat and washed. After washing, its contacts should be ringed, checking the resistance. If it is missing, the problem is not a blockage, the part has failed and needs to be replaced with a new one.

After installing the new valve, the assembly is assembled in the reverse order and a test run is carried out.

The machine does not drain water

The most common cause of this problem is a clogged drain system. The breakdown may also be due to a failure of the pump or control unit (the drain command is not given).

The process of removing clogs begins with cleaning the filter. The procedure can be represented as follows:

The filter cover, hidden behind the front panel at the bottom of the facade, opens slightly.
A flat dish is placed under it to collect the flowing water.
When the washing solution has completely drained, the filter is completely removed and washed.

If the blockage is severe, not only the filter can become clogged, but also the pump and even the drain hose. If cleaning does not lead to the desired result, it is necessary to check the serviceability of the pump.

Before you begin repairing the Ariston washing machine yourself, you need to dismantle the part in the following sequence:

Unplug the power cord from the outlet, disconnect the drain and inlet hoses.
Lay the car on its side and remove the bottom protection.
Disconnect the terminals, unscrew the clamps on the pipes.
Unscrew the screws holding the pump (1 or 4 depending on the model).

What you should be wary of:

the impeller is pushed forward;
strong backlash;
a large amount of scale in the filter seat.

To make sure the part is in good condition, you need to check the resistance of the motor windings. If it is absent (the norm is 140–180 Ohms), the pump is faulty and the winding may break. You can check the engine by connecting it to the network. If the pump is working properly, the impeller will begin to rotate.

No spin

There are three main reasons for this malfunction:

The motor failed and the drum stopped rotating.
The tachometer, which regulates the speed of rotation of the rotor, is faulty. The engine runs at minimum speed and the spin cycle does not meet the specified parameters.
The belt is broken.
Problems with the electronic module.
The water does not drain and the machine cannot start spinning.

It is very easy to check the last point - just drain the water through the filter or drainage tube and start the spin program.

To check the operation of the engine and the integrity of the belt, you need to remove the back cover of the device by unscrewing the fastening screws. A broken belt can be seen visually, but the motor will have to be examined in more detail.

To check the serviceability of the engine, it is necessary to measure the resistance on adjacent lamellas. It should be the same, within 0.2 Ohm. Sometimes wear on the slats can be seen visually. The part cannot be repaired - the engine must be replaced.

If the problem is not in the motor, you need to check the serviceability of the tachometer. The sensor is located on the shaft immediately behind the engine. It can be inspected and ringed without removing it from its seat.

The device is considered operational if the resistance it produces is about 60 ohms. In this case, you can check its contacts and how well it is secured to the shaft.

The door won't open

There may be several reasons why the hatch was blocked:

There is still water in the tank and the machine cannot open the door to avoid flooding.
The door handle mechanism is broken.
The hatch locking device is faulty.
Problems with the control module.

Before you begin the repair, you need to open the door by inserting a thin ruler under the hatch and squeezing the tongue or using an emergency cable (it can be found under the filter cover).

A faulty handle does not respond to pressure; if it breaks, it must be replaced with a similar one. The locking device located on the front panel must be removed by first unscrewing the bolts holding it and pulling off the cuff. The part rings and changes in the absence of resistance.

No heating

If the machine washes in cold water, most likely the heating element has become unusable. Replacing it is quite easy.

Troubleshooting proceeds according to the following scheme:

Remove the front panel.
Find the heating element at the bottom of the tank and test its contacts with a multimeter.
If there is no resistance, replace the part with a similar one.

The cause of the breakdown may be accumulated lime or mechanical wear of the heating element.

Leaking

You can determine the location of the leak by observing the washing machine during the washing process. If water appears while filling, the inlet hose is probably damaged. If during reset - drain hose or pipes.

Water that accumulates under the bottom during washing may indicate a leaky tank. If it flows down the front wall from the side of the hatch, it’s all a matter of a leaking cuff.

To restore the tightness of the joints, it is necessary to replace the leaky part with a new one, tightening the joints.

Doesn't take up water

The main reasons why the machine does not take in water:

clogged inlet hose;
Fill valve malfunction;
problems with the control module;
The pressure switch is faulty - without water it gives a signal that the tank is full.

All of the listed parts except the faulty module can be diagnosed and replaced at home.

The machine makes strange noise

The probable cause of the grinding noise is wear of bearings, shock absorbers, suspension springs, as well as foreign objects getting inside the drum.

Replacing bearings in Ariston vertical washing machines follows the following algorithm:

The device is disconnected from the electrical network and water supply.
Unscrew the screws from the back and front that hold the side panel and remove the panel.
Remove the pulley after first unscrewing the bolt holding it.
Having reached the hub, unscrew the screws and remove it from the seat.
Carefully knock out the bearing and seal.
An oil seal is installed in the hub, the bearing is pressed in, the place where the oil seal comes into contact with the shaft is cleaned and lubricated.
The hub is installed back, the car is assembled in the reverse order.

The bearing on the other side of the washing machine is changed according to the same principle, only without removing the pulley.

The bearing in front-loading Ariston washing machines changes according to a standard algorithm, like any other machine of this type.

Why doesn't the washing machine drain water?

Before you understand what to do if the washing machine does not drain water, you need to understand the causes of unit malfunctions. The washing process can be divided into several stages, and until one of them is completed, the program will not start the next one. For example, the rinsing mode is completed, however, the washing machine does not drain the water and hums (the next mode, spin, does not turn on), the laundry floats in it, and the operation of the unit stops. The main cause of this problem is a clogged drain system.

Most often this happens due to a clogged sewer pipe or a clog in the drain hose of the washing equipment. Similar malfunctions due to which water does not drain are the ingress of various objects into the concentrator, pipes and pump device. Common reasons for washer failure also include:

presence of air inside the pump;
mechanical failure of the concentrator;
damage to the pressure switch device;
insulation breakdown (break) of electrical wiring;
failure of the electronic control module.

Common causes of washing machine breakdowns also include damage to the pressure sensor and setting the wrong operating mode in which the unit operates.

Washing machine pressure switch

Equipment owners should pay attention to the operation of the washing machine, which will allow them to quickly detect failures and malfunctions.

If the machine has stopped draining water or it is happening more slowly than usual, this means that you need to diagnose the device for further troubleshooting. You should also pay attention to those cases when the machine begins to drain after one or two washes, the spin mode does not turn on, rinsing does not start after draining, as well as the equipment freezes (washing proceeds in the normal mode, as soon as the drain should turn on, the unit refuses execute the given program).

Troubleshooting the most common problems with the Ariston Margarita 2000 washing machine

You can repair the Ariston Margarita 2000 washing machine yourself if you follow the instructions below. The most common malfunctions of this device can be resolved as follows:

If the machine has stopped filling with water, but the sound of pouring water can be clearly heard in the upper part of the body on the left side, then you need to check whether the tap supplying water is open and whether the hose supplying water to the washing machine is not jammed. You can also check if the mesh on the filter is clogged.
The machine began to fill and drain water chaotically, but the specific hum of the pump is not heard, then you need to check at what height the drain hose is installed. This distance should not be less than 60 centimeters. The problem may be caused by the drain hose being disconnected due to vibration. To solve it, you need to return the hose to its place.
The device does not drain water. You can try to drain it manually using a drain filter, but before doing this you need to place a tray under the machine. It is also recommended to check the cleanliness of the filter and drain hose and, if necessary, clean them.
The machine has stopped executing software commands, namely the device responsible for selecting functions is constantly rotating in a circle. You need to take something metal with an insulated handle and set the switch handle to the black dot, then unplug the plug from the socket and short-circuit the outputs on the cord plug with this object. Thus, the residual voltage is removed from the device module and the program is reset.

Important! There may also be problems that you can easily solve by following the instructions from the articles below:
The machine knocks out when the SMA is turned on.
Replacing the rubber of the hatch.

Fault diagnosis

First of all, we checked how the washing machine is connected to the drain, since this is a common problem and often leads to unpredictable behavior of the SMA, especially Ariston of this series.

This is what our car looks like with the back cover removed.

It is connected to the drain correctly, and a siphon effect cannot occur, so we exclude this reason. Then we check the heating element. The tubular electric heater is located in the tank at the bottom, usually at the back of the washing machine. To access it, remove the back cover by unscrewing the screws with a Phillips screwdriver.

We call the resistance with the limit set at 200 Ohms. The heating element in question showed a value of 50 Ohms. Everything is fine here.

IMPORTANT! Before measuring, remove the terminals from the contacts! Because the heating element included in the electrical circuit may show incorrect resistance.

Then we check the heater for breakdown. To do this, set the maximum resistance limit that is available on the multimeter or tester. It is necessary to understand that megaohms are needed, and preferably 40 megohms. Otherwise, the result will be unreliable.

Then we apply one end of the probe to the body of the heating element, and the second in turn, first to the first contact, then to the other. If there is a breakdown, the tester will show a value other than 1.

Expert opinion

I work in the household appliance repair industry. Extensive experience in restoring washing machines and dishwashers.

Ask a Question

But again, this is not a 100% diagnosis!

Heating element of a washing machine with reset terminals.

In this case, the multimeter showed that there was no breakdown to the housing. We decided to conduct a more extensive diagnosis. Namely, they started the machine in the “wash” mode, with the heater previously turned off.

Expert opinion

I work in the household appliance repair industry. Extensive experience in restoring washing machines and dishwashers.

Ask a Question

Please note that not all machines will start with the heater turned off. And not everyone will go through the wash cycle completely.

Ariston, at least this model, starts without a heating element. What actually happened was that the machine took in water and the drum began to spin. There was no emergency drain!

For the purity of the experience, we connected our own heater to the washing machine. In this case, the SMA continued to function normally. When connecting your electric heater to the outside of the tank, you need to understand that heating in modern washing machines turns on 8-15 minutes after the start of the program. That is, during this period you don’t have to worry about overheating.

Connecting the heating element without changing it in the tank.

Problems with water heating

If during the washing mode the washing machine freezes for a long time, stops, does not heat up, or constantly drains water, the causes of the breakdown should be sought in the heating circuit. The device will signal these problems with codes F04 , F07 or F08 .

Failure of the heating element or pressure switch and codes F04, F07

In washing modes where heating is required, the error may appear immediately after startup, or after drawing water, but rinsing or washing in cold water will work normally. In this case, there are several options for solving the problem (besides the standard turn on/off the machine to reboot the controller).

If the code appears on the display during the washing phase or during startup (the machine does not even want to draw water), most likely the reason lies in the heating element itself. It can “pierce” onto the housing when the contacts come off or simply burn out.

To fix the problem, you need to get to the heating element, check all its connections, change the resistance with a multimeter (with a power of 1800 W it should produce about 25 Ohms).

If the device collects and then immediately drains water, the cause may be a breakdown of the pressure switch - the water level sensor. If there is a problem, this element can provide the controller with information that the heating element was not immersed in water, which is why the machine does not start heating.

In this case, it is necessary to check the water pressure sensor tube with the pressure switch (the hose may become clogged, kinked, frayed, or come off). At the same time, inspect the contacts of the sensor itself - they may need to be cleaned. But more precisely, code F04 - most likely, the part will require replacement.

In some cases, the problem may be in the board itself, faulty wiring or contact groups in the area from the board to the heating element or water level sensor. Therefore, you should ring all the elements of the control unit associated with the operation of the heating circuit, and if necessary, replace the burnt tracks or the controller itself.

Heating circuit faults and F08 symbol

If the water heating does not work correctly (or the machine “seems” that it starts when the tank is empty), error code F08 . The cause is most often a malfunction in the pressure switch circuit.

This problem can occur due to high humidity in the room, which negatively affects the controller. To make sure the board is in order, inspect it, wipe it dry, or blow it with a hairdryer.

Another simple solution to the issue could be the disconnected contacts of the heating element and the pressure switch, especially if the device was started for the first time after transportation. In other cases, a more professional inspection will be required with possible replacement of parts.

Possible malfunctions of Ariston machines, indicated by code F8:

If the washing mode is interrupted immediately after starting or during the washing phase and the device does not heat the water, the heating element will most likely need to be replaced.
If the machine stops after starting, when switching to the rinsing mode, or does not spin, it is possible that the contact group of the heating element relay is “stuck” on the controller when it is on. In this case, you can replace the failed elements of the microcircuit and, if necessary, reflash the board.
If the device “freezes” in various modes (and this can be either washing, rinsing or spinning), the wiring or contacts in the heater circuit may be damaged, or the pressure switch may break down, which considers that not enough water is entering the machine.

But if, when checking all the connections of the circuit and separately the pressure switch, the heating element relay and the heating element itself, no damage is detected, you will have to change the controller.

Step-by-step testing of Ariston machine malfunctions

It is recommended to repair the Ariston Margarita 2000 washing machine yourself only if you have a special service test. It allows you to easily detect any defect in the operation of the device and make repairs faster and easier. Next, we will learn how to run this test and check the operation of the machine.

Working with a service test

In order for the service test to start working, you will need the above-mentioned SAT diagnostic key. This tool has the following code - 95669. It allows you to launch an automatic testing program for the Margarita 2000 model. Then we connect the device to the connector and wait until the corresponding indicator lights up. First, the key will exchange information with the electronic controller for some time.

The testing program is launched as follows:

We check the connection of the machine to the water supply and sewerage system.
We inspect the tank for the presence of residual water in it; if there is any, then it must be removed immediately.
Close the hatch door tightly.
Set the selector knob to its original position.
Press the “AUTO TEST” button on the key and hold it.
As soon as the automatic testing starts, you will immediately hear a beep.

Important! During testing, the selector knob will automatically rotate, and at the same time, codes of the corresponding nature will be displayed on the panel. If the test detects an error, the indicator will stop constantly glowing and the light will start flashing, that is, indicating a fault code.

The number of flashes indicates the error code. Please note that when testing, the water inside the device will heat up to 30 degrees, so you need to set a water heating limit, turn off the spin functions and set any drying time.

Step-by-step execution of service testing

The process of diagnosing the Ariston Margarita 2000 washing machine can be roughly divided into several stages. Malfunctions and possible breakdowns are eliminated in the following sequence:

The fill valve for washing is selected and started in the main mode for 10 seconds.
Then the pre-wash starts for the same time in the same mode.
The hot water supply valve opens for 10 seconds.
The fill valves for the main and preliminary washes are turned on synchronously. Water will flow into the tank until the sensor signals that it is full.
The drum rotates first clockwise and then in the opposite direction.
The heating element turns on and the water warms up to 30 degrees.
The handle moves in the normal direction of rotation, and then stops in the 9th position.
The drain pump starts working. Moreover, it will function until the sensor reports that the tank is empty.
If the device is equipped with a drying mode, its fan will start working at this stage, and then the heating element will turn on and the air inside the tank will begin to warm up.
The selector knob moves to the reset position.
The program ends.

Important! If the malfunction of the Ariston Margarita 2000 washing machine was eliminated before the start of the test, then the service analysis simply will not start. To restart the machine in this case, you will need to turn it on for 10 seconds, disconnect the service key and start it again.

Cleaning the drain pipe

According to statistics, most often the drain does not work precisely because of a clogged pipe. You can only get to it through the bottom of the washer. Models with an open bottom are equipped with a pipe that is led out. You just need to put the equipment on its side, and the pipe will become visible. But models that have a tray or bottom cover require their removal, after which access to the pipe will again open. The Ariston washing machine, or rather its connection, has three connection points: a tank, a pump, and a pressure regulation hose.

The first task is to loosen the pipe clamps at each connection point. Afterwards you just need to move it to the side. In situations where the condition of the pipe is satisfactory, cleaning is performed using a special brush. They can carry out a thorough cleaning and then return the part to its original position. But if there is serious wear or serious damage, it will need to be replaced by installing it on the existing fasteners.

Interesting! You can carry out high-quality cleaning of the pipe with a solution of citric acid. To prepare it, you will need to take 2 liters of water, dissolve 100 grams of lemon juice in it, and then place the pipe in the resulting liquid for several hours. Afterwards, the part will need to be removed and washed thoroughly with cold water.

Diagnosis and troubleshooting

Program crash

Restart the program. Press start wash cycle and wait. If there is no reaction, turn off the machine and start draining.
Remove heavy objects from the lid and try to restart the drain.
If the problem is not solved, then the problem is not in the program.

Hose

Check the bend radius. Minimum 50, maximum 80 cm. If it is bent or not bent, then the water simply will not reach the drain. The machine will receive a signal to the built-in sensors, and the command will remain unfulfilled. You can fix the problem using a special clamp that comes with the washing machine.
Possible squeezing. This happens if you step on or knock over something heavy. The situation will not only stop the cycle, but also break the rubber. Remove any foreign objects.
Check the connection. The fastenings could come off, and the smart machine decided not to drown the neighbors below.

Sewerage

Open the tap or flush the toilet tank; if the water does not drain, you need to clean the system.
When disconnecting the drain source from the corrugation, the washing machine must be turned off.
Clear the blockage.

Filter

Turn off the power to the washing machine.
Place a towel underneath.
Open the filter protection. It is located at the bottom on the right side (if the car is facing the owner).
Turn the cap to the right and unscrew it.
Wait until the water stops flowing.
Remove the filter and inspect for excess contents: buttons, coins, washing powder.
Rinse the part. The water should not be hot.
Rotate the impeller (located behind the filter); if it moves freely and does not jam, then the pump is in order.

water pump

After draining the water and removing the filter, start the spin cycle.
If the impeller remains motionless, there may be a problem with the pump or pump.
When the pump makes an unusual noise, water has most likely leaked into it. In such cases it must be replaced.
To diagnose, you need to remove the lid of the washing machine.
You can fix the problem yourself if, after a visual inspection, minor damage is visible.
Did the examination yield no results? Then contact a specialist who carries out highly qualified repairs of Ariston machines.

Wiring

Remove the top cover and inspect the wires.
Perhaps the previous spin helped to disconnect the block of wires from the board. Return the block to its original position and restart Ariston.
Check for moisture or broken contacts

Starting the wash

The wash is started from the control panel, so you need to know at least the basic buttons. So, after turning on the machine, you need to press the power button on the control panel, next to the rotary knob for selecting programs. The desired program is selected by turning this knob clockwise only. You cannot rotate it counterclockwise! Having selected a program, you need to press the handle itself, the washing will start in 5 seconds.

The two lower large buttons are designed to select the spin speed or turn it off and to select the washing temperature. The panel also provides buttons such as:

stopping the machine during the washing process;
accelerated washing mode;
enhanced wash – a button that allows you to use pre-wash;
prewash.

When choosing a program, be careful. Pay attention to the labels on clothes, consider the type of fabric and be sure to sort items by color.

Care and safety rules

The machine's operating instructions cover not only installation and startup, but also care and safety rules. In order for the washing machine to work properly for a long time, you need to keep it clean. Here are some useful tips:

First of all, close the water tap after each wash.
Wipe the machine drum and rubber cuff with a dry cloth. This will prevent the appearance of mold and unpleasant odors.
It is best to rinse the powder cuvette in clean water and wipe it with a dry cloth.
Wash the outside of the car with warm water and a little soap.
Do not exceed the dosage of detergents, this will lead to the formation of a large amount of foam.
Before washing, check the contents of the pockets to ensure that foreign objects do not fall into the machine’s tank.
Carry out a dry wash every six months with a special machine cleaning product.
Check the drain filter regularly to remove debris and dirt.
During washing, do not touch the machine and keep your child away from the door.
Never open the door forcibly.
If there is a malfunction or unusual sound, turn off the water supply tap and unplug the machine.

We hope you found this brief information on using an Ariston washing machine useful. And you will find all the details in the full instructions, the link to which you can see below.

View full instructions

List of information codes and their decoding

Since washing machines of the Ariston and Indesit brands are produced by the same manufacturer, their information error codes are also the same. Let us consider in detail each of the nineteen alphanumeric combinations.

Error code F01

Most often, the F01 error code that appears on the screen indicates a short circuit in the engine management system. As a result, the connection between the motor and the control module is disrupted. Another reason for the lack of communication may be low voltage in the network.

To fix a problem without calling a technician, you need to have special skills: you will need to inspect the contacts of the electric motor, the harness connecting the motor to the control board. It is better to entrust checking the operation of connections and troubleshooting to professionals. You can independently try to disconnect the installation from the network and turn it on again after 10-15 minutes. If the error appeared as a result of a single malfunction of the control module, it will disappear.

Error code F02

Error F02 is also associated with problems with the electric motor. The cause of the malfunction may be a breakdown of the tachogenerator (speed sensor) or engine blocking, as well as a disruption in the supply of signals to the engine from the control board.

The tachometer controls the speed of the electric motor.

The engine may become blocked due to foreign objects getting into it or jamming of the bearings. Inspection of the engine, tachometer, controller and check of their wiring should be carried out by professionals.

Error code F03

Information code F03 occurs when the machine cannot heat the water to the required temperature. The cause of the malfunction may be a “sticking” relay of the heating element (tubular electric heater) or a breakdown of the temperature sensor. You can restore the machine's functionality by eliminating wiring faults or replacing broken parts.

Error codes F04 and F10

If the pressure switch - the sensor that controls the water level in the washing machine - does not work correctly, code F04 or F10 appears on the display. The cause of the malfunction may be either a breakdown of the sensor itself or a breakdown in communication between the sensor and the control board.

If error F04 appears, you can independently check the tube and contacts of the pressure switch

Most often, the pressure switch fails due to a violation of the integrity of the contacts or a clogged tube. You can fix such problems yourself. Replacement of the sensor or repair of the control board must be performed by a specialist.

Error code F05

Error F05 most often indicates that the pump cannot pump water out of the washing machine tank. This may be due to the following reasons: pump breakdown, clogged drain hose or filter, clogged sewer. If there is no water in the tank and the machine displays error F05, the water level sensor may be broken or the connection between it and the control module may be broken.

Poor water drainage may be caused by a clogged drain filter.

When the machine stops working with water in the tank, you need to drain the water before correcting the error. Emergency draining is performed using a regular drain hose or emergency connection, which is usually located behind a small door at the bottom of the front panel.

When error F05 appears, first check to see if there are any blockages in the drain hose or filter. Then inspect the pump, water level sensor and their contacts. It is better to entrust the replacement of faulty parts to a professional.

Error code F06

If information code F06 appears on the washing machine screen, this means that the buttons on the control panel are faulty. It is better to entrust the troubleshooting to a technician who will check the contacts and operation of the control module. You can independently verify that household appliances are connected to the network and that the socket and power cord are working properly.

Error codes F07 and F08

The washing machine displays error code F07 when it determines that the heating element is not covered with water when starting the wash. There may be several reasons for such a malfunction: failure of the heating element itself, the water level sensor or the control module. Difficulties with getting water can be caused by blockages in the hose or filter, as well as a lack of water in the water supply. Error code F08 is also associated with malfunctions of the heating element and water level sensor.

The heating element of a washing machine often fails due to the formation of limescale on its tubes

When error F07 or F08 appears on the screen, first check the presence of water in the house, then, if necessary, clean the fill hose and filter. If you were unable to fix the malfunction on your own, it is better to call a specialist, since it may be necessary to replace the heating element or pressure switch.

Error code F09

If information code F09 appears on the washing machine display, it means there has been a failure in the volatile memory. You can try to “fix” this problem by disconnecting the unit from the network and connecting it again after 10-15 minutes. If rebooting does not help, you need to call a technician.

Error code F11

When the machine cannot spin and drain water, code F11 appears on the display. Unlike error F05, in this case the cause of the malfunction lies only in the breakdown of the drain pump. If a part needs to be replaced, it is better to contact a specialist.

Error code F12

The appearance of code F12 on the screen indicates a lack of communication between the display module and the electronic controller. In such cases, the help of a specialist is required.

Error codes F13, F14 and F15

Codes F13, F14 and F15 are valid for Ariston washing machines with a clothes drying function. Malfunctions may include a breakdown of the temperature sensor or drying heating element, or a breakdown in communication between the devices and the control module.

Error code F16

The occurrence of code F16 is possible only in washing machines with vertical loading of laundry. The error lies in the blocking of the drum, for example, if the hatch in it was closed incorrectly. The drum can also become jammed due to foreign objects. In order not to cause even more damage to the equipment, it is better to entrust the troubleshooting to a specialist.

In Ariston top-loading machines, error code F16 indicates that the drum is blocked

Error code F17

If the washing machine hatch is not completely closed, information code F17 appears on the display. It happens that the door remains open due to negligence, but the most common causes of this error are foreign objects getting into the lock and deformation of the rubber cuff.

Open the door, carefully inspect the cuff and lock mechanism, remove foreign objects. If after checking the door still does not close, you should call a technician.

The rubber cuff located in the hatch of the washing machine may become deformed over time.

Error code F18

Error code F18 means the processor has failed. If a part burns out, it is replaced with a new one. Repairs must be carried out by specialists.

Error code H20

Information code H20 is displayed on the display when no water enters the tank. The most likely causes: lack of water in the water supply network, clogged hose, filter or water supply valve. If an error appears on the display of a new washing machine during the first wash, it means it is not connected to the pipes or sewerage correctly.

About errors in work

Any malfunctions of the Ariston Margarita 2000 (ALS88X) washing machine will not go unnoticed by the user. In the event of an emergency, the indicators on the unit flash and the control handle rotates chaotically. You can determine what exactly has gone wrong by the way the indicator blinks.

The most common fault codes are:

If the indicator blinks once with a certain frequency, it means the wires in the electric motor are shorted.
Flashing the indicator 2 times indicates a tachometer malfunction.
3 times – short circuit in the temperature sensor.
4 times – the pressure switch is faulty.
5 times – there is a need to clean the drain pump.
6 times - error
Flashing the indicator 7 times means the heating relay is stuck.
Flashing 8 times at periodic intervals means the heating relay is faulty.
Flashing 9 times indicates a software error.
10 times – pressure switch malfunction.
11 times drain pump failure.

To more accurately determine the nature of the malfunction, service center specialists connect a hardware key that connects to the computer. As soon as the red indicator on the control unit lights up, the operating cycle and self-diagnosis starts. During such testing, the technician identifies any problems with the washing unit. The computer displays washing machine errors and bearing failure that need to be fixed.

Ariston model error testing

If a malfunction is detected in the operation of the Ariston Margarita 2000 washing machine, the on/off indicator will immediately begin to flash, and the command knob will rotate chaotically. The blinking pattern of this indicator indicates a fault code.

The most common fault codes:

A short circuit has occurred in the electric motor circuits.
The connection with the tacheometers has been lost or the electric motor has jammed.
There is a break or short circuit in the temperature sensor.
The pressure switch is stuck in the “Empty” position.
The relay is stuck in the “Device full” position or there is a blockage in the drain pump.
An error occurred in the control function.
The heating relay is stuck.
The heating relay has stopped working.
The model is not EEPROM compatible.
The relay responsible for pressure began to simultaneously send signals that the device was “Filled” and “Empty”.
The drain pump has failed.

Important! To more accurately determine the malfunction, specialists use a special tool, namely a hardware key. It can be connected to a computer and initiate a wash, during which the machine will perform self-diagnosis. It is inserted into a special hole located on the back wall of the device. If everything is done correctly, the red indicator on the unit will light up, that is, it will be possible to begin self-testing.

Features of AVSL 100 repair

Sometimes owners of AVSL 100 machines encounter problems whose solutions are not so obvious:

The washing machine interrupts the program before spinning or rinsing. If the device is disconnected from the network and then turned on again, the unit will complete the process. The likely problem is a faulty drain pump that jams from hot water.
The device freezes during operation and the fault is not detected. After cooling, the washing machine resumes washing. The probable cause is wear of the motor brushes; they need to be replaced with new ones.

In general, malfunctions of washing machines of this series can be considered typical.

Communities › Do It Yourself › Blog › The washing machine is broken, I need advice.

Hi all! I saw a post that they helped a person with a washing machine, maybe good luck will happen to me too?) I’ve been suffering with it for a long time... =(

In general, I have an Ariston Margherita 2000, the situation is as follows, sometimes you turn on the machine, on any program, it fills with water, immediately drains, and the drum (where you select modes) just starts clicking and spinning clockwise without stopping. Such nonsense in any program, you have to turn off the machine, wait 5 minutes, and turn it on again, and at what time it will start working normally, you can’t guess... If anyone has come across this animal and knows how to tame it, please, help me )))

In general, making the drain higher is not an option, it still drains.

( 1 rating, average 5 out of 5 )

How to detect a leak?

One of the very first reasons that the machine drains water immediately when turned on is the Aquastop system. This useful design, when a leak is detected, automatically blocks the flow of water and starts draining to prevent a flood. If you are the owner of a Bosch dishwasher, the self-diagnosis system will notify you of a problem by displaying fault code E15. Also, after listening, you will notice that water is not being collected.

To fix the problem, you need to drain the water from a special pan. You also need to remove water from the anti-leak system sensor itself. To rid the machine parts of water, tilt the machine body away from you by 45 degrees. The same operation will help you if no leak is detected, but the AquaStop system sensor is simply stuck.

On a note! Inexpensive dishwashers have a mechanical sensor installed instead of an electrical sensor, so when the anti-leakage system is triggered, the entire hose must be replaced.